Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 23
Search took 0.22 seconds.
Search: Posts Made By: bluecobra
Forum: 1997 - 2003 F150 05-28-2016, 01:05 PM
Replies: 3
Views: 221
Posted By bluecobra
Engine turns over but will not start

2001 F-150 5.4 extended cab

You have probably seen this before. Engine cranks but will not start. Backed into driveway, loaded recyclables, truck would not start. Fuel pump relay clicks, a...
Forum: 1997 - 2003 F150 03-16-2016, 05:53 PM
Replies: 4
Views: 367
Posted By bluecobra
2001 5.4 It is a steel tube, part of the heater....

2001 5.4 It is a steel tube, part of the heater. You shouldn't have to mess with it. If you want to disconnect the heater hoses, there is a tool for that. You can reuse the fittings with regular...
Forum: 1997 - 2003 F150 03-16-2016, 05:43 PM
Replies: 6
Views: 249
Posted By bluecobra
2001 5.4 Had similar issue. Leakage causing #1...

2001 5.4 Had similar issue. Leakage causing #1 misfire. Intake manifold had a small crack that I found after pulling it. They can also warp and can be epoxied in some cases. I went with the $160...
Forum: 1997 - 2003 F150 02-26-2016, 07:56 AM
Replies: 4
Views: 384
Posted By bluecobra
Thanks...I'll check those.

Thanks...I'll check those.
Forum: 1997 - 2003 F150 02-25-2016, 02:13 PM
Replies: 4
Views: 384
Posted By bluecobra
Dome light stays on

2001 F150 4x4 extended cab


When the door is opened, the dome light and the light on the back of the cab comes on. When the engine is started, the lights are supposed to go off. Now the lights...
Forum: 1997 - 2003 F150 07-01-2014, 03:50 PM
Replies: 6
Views: 894
Posted By bluecobra
Got bearings & seal for the 9.75. Pulled the old...

Got bearings & seal for the 9.75. Pulled the old ones and discovered the the 9.75
bearings were too big. It took the 8.8 bearings instead. Go figure!
Forum: 1997 - 2003 F150 06-25-2014, 06:00 PM
Replies: 6
Views: 894
Posted By bluecobra
Thanks Bluegrass, I did get under and its a...

Thanks Bluegrass,

I did get under and its a 9.75 RG.
Forum: 1997 - 2003 F150 06-25-2014, 10:57 AM
Replies: 6
Views: 894
Posted By bluecobra
Ring Gear Size

I have an 2001 F-150-5.4-4wd-H-9 diff.


Looking on RA to buy rear axle bearings. How can I tell if the ring gear is 8.8 or 9.75. I have seen posts that said if the diff cover has 10 nuts its 8.8...
Forum: 1997 - 2003 F150 05-22-2013, 06:44 PM
Replies: 6
Views: 1,403
Posted By bluecobra
I agree with Mr BIG

I agree with Mr BIG
Forum: 1997 - 2003 F150 03-27-2013, 06:52 PM
Replies: 2
Views: 843
Posted By bluecobra
COP question

2001 with 5.4 160K.
This past weekend I started having a missfire. A quick look under the hood and spotted a heater hose leaking onto the #1. Repaired the hose, removed coils 1,2,3 and blew out all...
Forum: 1997 - 2003 F150 11-17-2012, 08:16 AM
Replies: 2
Views: 434
Posted By bluecobra
there's a post by Plug-n-Jug on 11-12 that...

there's a post by Plug-n-Jug on 11-12 that details the core replacement.
Forum: 1997 - 2003 F150 11-14-2012, 11:07 AM
Replies: 3
Views: 1,732
Posted By bluecobra
You should find a schematic of the vac lines on...

You should find a schematic of the vac lines on the sheild on top of the radiator. I can see the PVC on the valve cover.
Forum: 1997 - 2003 F150 09-01-2012, 04:08 PM
Replies: 2
Views: 392
Posted By bluecobra
Smile Check out this site for some great how to troubleshooting.

Stumbled on this site looking for help with some elusive engine problems. Hope this is useful.

HOW TO TEST IGNITION CONTROL MODULES and MASS AIR FLOW SENSORS and MORE. Easy, simple and fast...
Forum: 1997 - 2003 F150 08-28-2012, 12:48 PM
Replies: 2
Views: 381
Posted By bluecobra
I've checked the pvc line and gone over every...

I've checked the pvc line and gone over every line I could find. Replaced some. What is the VM Valve? Also, one of the lines I replaced was the one going from the brake booster to the TB. ...
Forum: 1997 - 2003 F150 08-28-2012, 10:47 AM
Replies: 2
Views: 381
Posted By bluecobra
Engine wants to surge.

2001 F150 5.4 4x4 148K

I recently replaced the intake manifold on this truck and when the engine revs it wants to continue at high RPMs for about 10 seconds after letting off the throttle. When...
Showing results 1 to 15 of 23

 
Forum Jump
 


All times are GMT -5. The time now is 01:48 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup