Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 500
Search took 0.19 seconds.
Search: Posts Made By: drptop70ss
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 10:17 PM
Replies: 24
Views: 1,169
Posted By drptop70ss
Agreed on crimping making the channels one time...

Agreed on crimping making the channels one time use. The seals I installed will stay in place with no adhesive or crimping, once in place you cannot get them to slide or move in the channel at all....
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 07:55 PM
Replies: 6
Views: 100
Posted By drptop70ss
Sounds like the master needs a rebuild, assuming...

Sounds like the master needs a rebuild, assuming there really is no air in the system.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 07:47 PM
Replies: 24
Views: 1,169
Posted By drptop70ss
Not sure is that is needed or not, my seals stick...

Not sure is that is needed or not, my seals stick out past the channel and look to be sealing ok against the door. They do fit tight enough in the channel that they will not move. I am going to try...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 07:40 PM
Replies: 9
Views: 240
Posted By drptop70ss
I have to get a better side picture but my truck...

I have to get a better side picture but my truck #2 has the same stance. Wheel size alone will not get you there, the suspension setup is more important.
...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 07:15 PM
Replies: 380
Views: 50,588
Posted By drptop70ss
Both doors assembled, just have to clean up the...

Both doors assembled, just have to clean up the inside door handles and put them on.
Knocking out the mini projects to get this truck finished.
Replaced the right side lower door channel,...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 03:15 PM
Replies: 8
Views: 210
Posted By drptop70ss
I have read threads on the aftermarket valves...

I have read threads on the aftermarket valves leaking, so I was weary of using one, but my stock of OEM stuff is drying up and good used pre ABS valves cost more than the aftermarket ones.
So far I...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 01:53 PM
Replies: 24
Views: 1,169
Posted By drptop70ss
Just to update this, I am finishing up the last...

Just to update this, I am finishing up the last few details on my truck #2 build, including the lower door seals. I have found as others did that no way will the new seal fit my original seal...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-22-2016, 07:12 PM
Replies: 3
Views: 133
Posted By drptop70ss
Inline fuel pressure gauge would show pump...

Inline fuel pressure gauge would show pump function. Could just be a stuck float or trash in the carb.
Just got my massey 135 tractor out for the first time in a couple years, did the same thing...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-22-2016, 07:09 PM
Replies: 11
Views: 216
Posted By drptop70ss
You could install an inline fuel filter with a...

You could install an inline fuel filter with a glass case near the carb, then you can see if the fuel is in the line after the truck sits.
Are you pumping the pedal while you are cranking it?...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-22-2016, 06:02 PM
Replies: 8
Views: 210
Posted By drptop70ss
For 4 wheel discs I put one of these on my truck....

For 4 wheel discs I put one of these on my truck.

https://www.summitracing.com/parts/sum-760185/overview/

If you dont want a distribution block you can install one of these in the rear line
...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-22-2016, 03:52 PM
Replies: 8
Views: 210
Posted By drptop70ss
what are you running? 4 wheel disc, 4 wheel drum,...

what are you running? 4 wheel disc, 4 wheel drum, or front discs and rear drums?
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-21-2016, 02:24 PM
Replies: 46
Views: 2,325
Posted By drptop70ss
Good luck on the build from another New Yorker! I...

Good luck on the build from another New Yorker! I can only see some of your pictures for some reason but it looks like a great project.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-19-2016, 08:38 PM
Replies: 380
Views: 50,588
Posted By drptop70ss
One door done! Quite the rubix cube of assembly,...

One door done! Quite the rubix cube of assembly, found out the hard way that the window regulator has to go in before the divider bar!
...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-19-2016, 08:30 PM
Replies: 16
Views: 460
Posted By drptop70ss
I dont care what the truck is or was, I was...

I dont care what the truck is or was, I was laughing my arse off when that thing stood up on the trailer hitch. My best day at work just doesnt compare to that!
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-19-2016, 08:25 PM
Replies: 5
Views: 197
Posted By drptop70ss
I would make a raised mount for the ratchet...

I would make a raised mount for the ratchet shifter. I think I have had just about all of them, B/M quicksilver unit was always my favorite. Simple enough to use and has full ratchet action when...
Showing results 1 to 15 of 500

 
Forum Jump
 


All times are GMT -5. The time now is 06:01 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup