Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 137
Search took 0.41 seconds.
Search: Posts Made By: lm987
Forum: Clutch, Transmission, Differential, Axle & Transfer Case Yesterday, 01:43 PM
Replies: 0
Views: 79
Posted By lm987
Ford 9 inch Pinion Bearing Retainer

Greetings,
I have just rebuilt a Ford 9 inch and am having trouble installing the retainer that holds the tail end of the pinion bearing in the case. Is there a special way to install it??
Thanks
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-14-2016, 02:43 PM
Replies: 0
Views: 152
Posted By lm987
Drag Link Question

Greetings,
I have a question regarding the drag links on the F-1 trucks. The one on my 1950 F-1 is straight while I have seen others that have a slight bow in them. Is there a difference in what...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 10-30-2015, 01:25 PM
Replies: 13
Views: 338
Posted By lm987
Spring Hangers

Greetings,
Regarding your spring hangers; I have a pair of NOS front hangers but only the ones that go on the inside of the spring..(ones with the bends). I also have a pair of used ones that fit on...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 10-29-2015, 12:30 PM
Replies: 13
Views: 338
Posted By lm987
Spring Hangers

Greetings,
I have both front and rear NOS spring hangers. If I have any extras I will let you know.
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 10-19-2015, 12:51 PM
Replies: 1
Views: 239
Posted By lm987
Timing Issue

Greetings all.
I have a new 302 installed in my 1950 F-1. My problem is that I have to rotate the distributor so far clockwise to get it to start that the front of it it interferes with the...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 09-28-2015, 01:07 PM
Replies: 2
Views: 241
Posted By lm987
low Vacuum

Thank you. This does help!
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 09-26-2015, 02:48 PM
Replies: 2
Views: 241
Posted By lm987
302 low vacuum

Greetings all,
I have a newly rebuilt 302 in my '50 F-1. My issue is that the engine is supposed to pull a vacuum of 18-21 lbs. but I am only getting 14 inches at ~700 rpm idle. The needle is steady...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 09-05-2015, 02:27 PM
Replies: 9
Views: 459
Posted By lm987
Bed Sides

Greetings,
When I had my F-1 painted and some body work done the body man suggested having the inside of the bed sides coated with "Line X". I had it professionally done and the bed sides are now...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 06-09-2015, 11:49 AM
Replies: 4
Views: 392
Posted By lm987
Thanks Baddad. This helps!

Thanks Baddad. This helps!
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 06-08-2015, 06:19 PM
Replies: 4
Views: 392
Posted By lm987
TOP DEAD CENTER

Greetings all.
I have 71 Ford 302 and want to find top dead center using a piston stop. I am confused on the initial setting of the stop. How do you know how far to adjust the end that contacts the...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-13-2015, 05:28 PM
Replies: 4
Views: 748
Posted By lm987
Hood Hinges

Somewhere along the way there was a design change. My '50 F-1 (early) has two internally threaded studs on each side of the hood. The outer diameter of the studs is the same as the holes in the...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-13-2015, 02:03 PM
Replies: 4
Views: 748
Posted By lm987
hood hinges

Greetings,
Do you have the right hinge bolts? Based on your hood design, some use non-shouldered bolts. I had a similar issue until I got non- shouldered bolts.
Good luck!
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 04-04-2015, 12:53 PM
Replies: 7
Views: 523
Posted By lm987
9 inch axles

All, Thanks for your help. I was getting worried that I perhaps had an issue.

I used the original rear brake cables with the 1970 F-1 housing in my F-1 and they worked fine.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 04-03-2015, 01:47 PM
Replies: 7
Views: 523
Posted By lm987
Ford 9 inch Axles

Greetings all.

I have searched the forums but cannot find an answer to this question:

Do all Ford 9 inch differentials have two different axle lengths??

I have a 1970 F-1 differential and...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 04-03-2015, 01:35 PM
Replies: 5
Views: 467
Posted By lm987
DRAG LINK

Maybe I am confused but don't you just have to unscrew the plug at the end of the drag link and remove the spring and spacers?
Showing results 1 to 15 of 137

 
Forum Jump
 


All times are GMT -5. The time now is 09:15 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup