Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 500
Search took 0.27 seconds.
Search: Posts Made By: 68Mercury250Ranger
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-19-2016, 12:25 AM
Replies: 41
Views: 1,493
Posted By 68Mercury250Ranger
damn I've been waiting for the bigblock 6spd...

damn I've been waiting for the bigblock 6spd unicorn :) you guys are just mean............... :(
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-19-2016, 12:02 AM
Replies: 42
Views: 770
Posted By 68Mercury250Ranger
you got it! have to correct some ...

you got it!


have to correct some misinformation .......
F250 D44 TTB has no parts that will fit the F150 TTB other than the locking hub mechanisms and the R&P . been there with a bronco...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-18-2016, 07:39 PM
Replies: 42
Views: 770
Posted By 68Mercury250Ranger
now that is a good question, check your axle...

now that is a good question, check your axle code on the door jam sticker. 3.08s are common in 4wd TTB, I've seen several Broncos with 5.8s with 3.08s and limited slip.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-18-2016, 08:48 AM
Replies: 42
Views: 770
Posted By 68Mercury250Ranger
F250 TTB were made with a dana44 front but not...

F250 TTB were made with a dana44 front but not sure how far into production, have owned a few, a 1985, a 1988 and a 1989. but haven't seen any built later than that. if they have the small locking...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-17-2016, 10:35 PM
Replies: 42
Views: 770
Posted By 68Mercury250Ranger
if you were going with 33" tires there are a lot...

if you were going with 33" tires there are a lot of option out there for 15's and 16s.


some 5x5.5 16" ford van rims (or Dodge shhhhhh) for the front and 8bolt for the rear would get you into...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-17-2016, 10:13 PM
Replies: 7
Views: 190
Posted By 68Mercury250Ranger
check and make sure you tightened all your...

check and make sure you tightened all your starter connections. ground cables. with new batteries and starter you have everything else covered regarding cranking speed.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-17-2016, 09:59 PM
Replies: 42
Views: 770
Posted By 68Mercury250Ranger
if you aren't worried about 5 bolt wheels on the...

if you aren't worried about 5 bolt wheels on the front and 8 bolt on the rear, just swap the front ring/pinion or complete centre section from a 4.10 F150.


you could have your swap done in a...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-17-2016, 09:45 PM
Replies: 42
Views: 770
Posted By 68Mercury250Ranger
the rear end is a bolt in, same 3" rear leafs...

the rear end is a bolt in, same 3" rear leafs F250 and F150 4x4s


F250 TTB has no parts that interchange onto the F150 TTB.


ring and pinion might fit from an early F250 TTB but that's...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-17-2016, 02:51 AM
Replies: 10
Views: 386
Posted By 68Mercury250Ranger
wide 33s will not fit well with no lift., as for...

wide 33s will not fit well with no lift., as for enough power with 33s and 3.55 gears , that depends on what you are doing with the truck and if you have a stick or an automatic . 300 6cyl is a...
Forum: 1968-2013 Full Size Vans 01-17-2016, 02:23 AM
Replies: 9
Views: 346
Posted By 68Mercury250Ranger
no , not the same, no parts interchange. ok...

no , not the same, no parts interchange. ok maybe the kingpins themselves are the same but even the wedge bolt location is different.
Forum: 1968-2013 Full Size Vans 01-17-2016, 02:18 AM
Replies: 18
Views: 2,391
Posted By 68Mercury250Ranger
460 from a stock pre 92 Eseries, unbolt>bolt it...

460 from a stock pre 92 Eseries, unbolt>bolt it back up. all the conversion parts you need...... put a zero timing chain and gears, a highvolume oil pump in it and rebuild the carb. low cost...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-14-2016, 01:22 AM
Replies: 5
Views: 374
Posted By 68Mercury250Ranger
have to watch the offset on your rims and how...

have to watch the offset on your rims and how wide your 33s are. if your truck is an ex plow truck or front springs are beat, it might be a clearance issue. I've run 255/85/16s on a stock 1983 150...
Forum: 1968-2013 Full Size Vans 01-14-2016, 01:13 AM
Replies: 18
Views: 2,391
Posted By 68Mercury250Ranger
460 , 460, 460. minor tweaks and it is one...

460 , 460, 460. minor tweaks and it is one scary powerfull vehicle.


I prefer the big diesels but my fuel is double the cost of yours...............
Forum: 1968-2013 Full Size Vans 01-14-2016, 01:05 AM
Replies: 3
Views: 192
Posted By 68Mercury250Ranger
offy makes a goo ddual plane 4barrel intake and...

offy makes a goo ddual plane 4barrel intake and it recomends 450-500cfm carb. factory efi manifolds are awesome too.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-10-2016, 02:12 AM
Replies: 13
Views: 327
Posted By 68Mercury250Ranger
supercab seat fits bronco. bolt in , they used...

supercab seat fits bronco. bolt in , they used the same floor pan.


crew and regular cab 40/20/40 much harder to find around here.
Showing results 1 to 15 of 500

 
Forum Jump
 


All times are GMT -5. The time now is 12:49 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup