Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 498
Search took 0.17 seconds.
Search: Posts Made By: JohnSmith3524
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-01-2016, 03:36 PM
Replies: 10
Views: 277
Posted By JohnSmith3524
for optimum timng settings..

I would buy a vaccum gauge and set the timing...also adjust your carb for best vacuum...

it's a google'able concept..

upon re-reading.(unless your original post was a typo).I would change your...
Forum: 1978 - 1996 Big Bronco 11-09-2015, 03:36 PM
Replies: 10
Views: 854
Posted By JohnSmith3524
bump

edit ..new material
Forum: 1978 - 1996 Big Bronco 11-08-2015, 03:46 PM
Replies: 37
Views: 1,122
Posted By JohnSmith3524
hey there..

The harness I can offer is the one that begins at the L/R taillight assembly area and goes to the tailgate motor. This harness also includes the feed wire for the defrost circuit. This harness btw...
Forum: 1978 - 1996 Big Bronco 11-05-2015, 01:18 PM
Replies: 37
Views: 1,122
Posted By JohnSmith3524
Sounds like a good plan. If you DO want to wire...

Sounds like a good plan. If you DO want to wire in that window, if I get around to I have an straight rear harness with the wire involved that does this. I also have an extra paddle, harness I'm...
Forum: 1978 - 1996 Big Bronco 11-05-2015, 12:50 PM
Replies: 37
Views: 1,122
Posted By JohnSmith3524
Been following your saga bro, something must be...

Been following your saga bro, something must be wrong with the glass? About your new weatherstripping, is it NOS or a repop from graveyard? I have done a lot of work on my rear glasses and have NOT...
Forum: 1978 - 1996 Big Bronco 11-05-2015, 12:40 PM
Replies: 10
Views: 854
Posted By JohnSmith3524
Well

I have two Broncos. One is a convertible with a soft top, (with the glass and all hardware removed making that gate very light btw), the other has the "safety" switch bypassed with a jumper. It...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 09-08-2015, 02:32 PM
Replies: 27
Views: 1,386
Posted By JohnSmith3524
it CAN be..

Depending on what type of choke coil you have...(inside that black round housing) you CAN utilize a piece of tubing wrapped around one of your exhaust pipes so as to heat the air sufficiently to...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 09-08-2015, 02:15 PM
Replies: 27
Views: 1,386
Posted By JohnSmith3524
on point..

if you're going to utilize your choke..this should be connected properly...(unless you choose to go "all electric" or manual)...

the bottom port could be used for a general vacuum feed primarily...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 08-06-2015, 07:13 PM
Replies: 7
Views: 463
Posted By JohnSmith3524
just another thought..

When my 85' Bronco R/A experienced a failed pinion shaft nose bearing..The vibratiion was getting bad enuf so as to make me actually take it out. In the process you can determine whether or not you...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 07-24-2015, 12:30 PM
Replies: 16
Views: 813
Posted By JohnSmith3524
about the valvetrain

remember that EFI heads use pedestal rockers..something you may have to deal with while adapting on older head to the block...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 07-17-2015, 11:02 AM
Replies: 10
Views: 599
Posted By JohnSmith3524
a few thoughts

I'll assume you meant to say NP435 (granny low).. With all of that in top running shape including the cat test pipe that has been mentioned, I would test it at a maximum of 50-55mph and see what you...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 06-23-2015, 06:31 PM
Replies: 75
Views: 4,624
Posted By JohnSmith3524
x2 on the above mod..it works..great gasket ...

x2 on the above mod..it works..great gasket

re: the particular 1639 vc gasket..since it's rubberizd cork it can be torqued carefully and reused after gluing it to the clean valve cover side should...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 06-20-2015, 12:26 PM
Replies: 75
Views: 4,624
Posted By JohnSmith3524
personal favorite for the valve...

personal favorite for the valve cover..http://www.summitracing.com/parts/fel-1639

Oil pan...http://www.summitracing.com/parts/fel-os34601r/overview/
Forum: Ford Inline Six, 200, 250, 4.9L / 300 06-18-2015, 12:17 PM
Replies: 114
Views: 7,302
Posted By JohnSmith3524
I have to say, I have really enjoyed the factory...

I have to say, I have really enjoyed the factory Holley manual choke that came on my 570. Fully adjustable...of course cable operated..
Forum: Ford Inline Six, 200, 250, 4.9L / 300 06-18-2015, 12:12 PM
Replies: 11
Views: 844
Posted By JohnSmith3524
I finally got a filter adapter installed on my...

I finally got a filter adapter installed on my new DD (my e150). When I change the oil I usually drain the pan "while it's hot"..then use a a plastic bag to catch the mess as I loosen the cold...
Showing results 1 to 15 of 498

 
Forum Jump
 


All times are GMT -5. The time now is 02:48 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup