Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 335
Search took 0.26 seconds.
Search: Posts Made By: 1973dieselhighboy
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel Today, 06:11 PM
Replies: 2
Views: 89
Posted By 1973dieselhighboy
Yes this is were your supply and return lines for...

Yes this is were your supply and return lines for the engine run. They run on the top of the frame rail and are hard lines if I remember correctly and then have a short rubber hose that connects to...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel Today, 06:08 PM
Replies: 2
Views: 80
Posted By 1973dieselhighboy
Under certain circumstances it will but not...

Under certain circumstances it will but not always.
If you run the truck wide open and the pcm commands the ipr to close off some and icp can not reach desired pressure it will set a check engine...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 02-01-2016, 02:11 AM
Replies: 4
Views: 183
Posted By 1973dieselhighboy
Program the keyless entry with your fabs. Program...

Program the keyless entry with your fabs. Program the fabs first and before it times out out your code in the keyless entry and then it should honk just like when you programmed your fabs
Forum: 6.0L Power Stroke Diesel 02-01-2016, 02:09 AM
Replies: 47
Views: 682
Posted By 1973dieselhighboy
To do a air check on the hpo system you need to...

To do a air check on the hpo system you need to have a ground and positive wire hooked to the ipr then apply air pressure to the rail and when you start hearing the air leak out you will then supply...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 02-01-2016, 01:59 AM
Replies: 30
Views: 577
Posted By 1973dieselhighboy
Cause with it unplugged the needle inside the ipr...

Cause with it unplugged the needle inside the ipr is not blocking the exhaust port to the crankcase. The ipr is wide open and exhausting all hpo to the crankcase. When you crank the engine the pcm...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 01-31-2016, 06:54 PM
Replies: 4
Views: 198
Posted By 1973dieselhighboy
Yes it will but it is a great time to change oil

Yes it will but it is a great time to change oil
Forum: 1999 - 2003 7.3L Power Stroke Diesel 01-28-2016, 09:37 PM
Replies: 12
Views: 396
Posted By 1973dieselhighboy
I had the same thing happen a few years ago...

I had the same thing happen a few years ago running 238/100 and we had found when we starting digging into the tuning is that I was to advanced on the bottom end and it had slowly hammered the crank...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 01-09-2016, 11:24 AM
Replies: 13
Views: 241
Posted By 1973dieselhighboy
I got my bearings at Napa in November and it was...

I got my bearings at Napa in November and it was under 10 bucks in the middle of nowhere in Oregon if I remember they were 6203 bearings
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 01-07-2016, 09:07 PM
Replies: 23
Views: 459
Posted By 1973dieselhighboy
And before someone decides to correct me on the...

And before someone decides to correct me on the flywheel. With the 80s idi with a c6 they ran a 2 piece flywheel which is cast and then the flex plate that is how ever thick bolts up to the crank...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 01-07-2016, 09:03 PM
Replies: 23
Views: 459
Posted By 1973dieselhighboy
I have a 86 c6 in my shed but I don't have an...

I have a 86 c6 in my shed but I don't have an e4od to compare to and the issue with running an idi flex plate is if I remember don't quote me on it is idi is external balance and powerstroke is...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 01-07-2016, 08:19 PM
Replies: 23
Views: 459
Posted By 1973dieselhighboy
I know there is a difference between a flex plate...

I know there is a difference between a flex plate and flywheel but idi engines have both with the c6 in 88.

I am putting a manual valve body in so I will shift it not the trans shifting so I...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 01-07-2016, 04:24 PM
Replies: 23
Views: 459
Posted By 1973dieselhighboy
C6 behind power stroke

As the title says, has anyone put a c6 behind a powerstroke.

Can I run the stock powerstroke flywheel and if so what torque converter will bolt to the flywheel and work with the c6.

Reason I...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 12-29-2015, 10:14 PM
Replies: 21
Views: 444
Posted By 1973dieselhighboy
Is the input gear and 3rd gear damaged from...

Is the input gear and 3rd gear damaged from something going threw them or is it pitted. Does the counter shaft look in good condition and no pitting
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 12-28-2015, 09:50 PM
Replies: 21
Views: 444
Posted By 1973dieselhighboy
Well that would make since but if the input gear...

Well that would make since but if the input gear and 3rd gear ( you referred to 4th) is chewed up then the counter shaft is probably not in the greatest shape either and probably needs replaced at...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 12-27-2015, 10:34 PM
Replies: 21
Views: 444
Posted By 1973dieselhighboy
Pocket bearing sounds right

Pocket bearing sounds right
Showing results 1 to 15 of 335

 
Forum Jump
 


All times are GMT -5. The time now is 10:28 PM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup