Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 499
Search took 0.11 seconds.
Search: Posts Made By: f5fordgirl
Forum: Ranger & B-Series 01-11-2016, 12:33 PM
Replies: 3
Views: 215
Posted By f5fordgirl
At that age the windshield rubber may be hard and...

At that age the windshield rubber may be hard and cracked, or just hard and not sealing against the glass.
Forum: Ranchero & 1961 - 1967 Econoline 01-07-2016, 06:17 PM
Replies: 5
Views: 183
Posted By f5fordgirl
My uncle has a bell for a C4 to match a 351M 400.

My uncle has a bell for a C4 to match a 351M 400.
Forum: FE & FT Big Block V8 (332, 352, 360, 390, 406, 410, 427, 428) 01-04-2016, 08:01 AM
Replies: 15
Views: 457
Posted By f5fordgirl
It has to be in a certain position to get all the...

It has to be in a certain position to get all the bolts in.
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 01-01-2016, 05:42 PM
Replies: 11
Views: 282
Posted By f5fordgirl
On the valve cover tag, at the front bottom, it...

On the valve cover tag, at the front bottom, it says 1981.
Forum: Y-Block V8 (239, 272, 292, 312, 317, 341, 368) 12-25-2015, 06:33 PM
Replies: 2
Views: 257
Posted By f5fordgirl
The number one suspect for leaking oil is the...

The number one suspect for leaking oil is the valve and lifter cover gaskets.
Forum: FE & FT Big Block V8 (332, 352, 360, 390, 406, 410, 427, 428) 12-20-2015, 02:04 PM
Replies: 5
Views: 250
Posted By f5fordgirl
A weak coil will cause low spark, and not a good...

A weak coil will cause low spark, and not a good burn in the cyl's, so the unburnt gas backfires in the hot exhaust/.
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 12-02-2015, 07:37 AM
Replies: 20
Views: 632
Posted By f5fordgirl
If you put 1 through 4 in, then added 5 through...

If you put 1 through 4 in, then added 5 through 7, and it was fine, but got tight when #8 was put in, that's where you should start looking for the probem. It might be that cyl, or piston has a...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 11-28-2015, 11:40 AM
Replies: 1
Views: 178
Posted By f5fordgirl
If the drum rubs the backing plate during turns,...

If the drum rubs the backing plate during turns, it sounds like loose bearings. As for centering the shoes, the springs are what do that.
Forum: Ranger & B-Series 11-08-2015, 08:06 AM
Replies: 8
Views: 256
Posted By f5fordgirl
Check the condition of the clutch system, and the...

Check the condition of the clutch system, and the pilot bearing.
Forum: Ranger & B-Series 11-06-2015, 02:30 PM
Replies: 10
Views: 543
Posted By f5fordgirl
A master overhaul kit is over $500. then machine...

A master overhaul kit is over $500. then machine shop work on the head, bore the block, maybe turn the crank will come to over $1200. A re ring is a lot cheaper, but engine may be just at the point...
Forum: 3.8 & 4.2L V6 11-02-2015, 07:46 AM
Replies: 1
Views: 318
Posted By f5fordgirl
The tension should be normal because some valves...

The tension should be normal because some valves will be pushed down.
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 10-14-2015, 05:33 PM
Replies: 6
Views: 285
Posted By f5fordgirl
Did the engine you bought have a dist, is it and...

Did the engine you bought have a dist, is it and the new one the same length from mounting flange to bottom?
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 10-14-2015, 05:23 PM
Replies: 11
Views: 236
Posted By f5fordgirl
Might be broken gear in the trans pump, have you...

Might be broken gear in the trans pump, have you checked the pan for metal pieces?
Forum: 335 Series- 5.8/351M, 6.6/400, 351 Cleveland 10-08-2015, 12:53 PM
Replies: 3
Views: 255
Posted By f5fordgirl
If you do decide to prime it, the dist will need...

If you do decide to prime it, the dist will need to come out, mark where the rotor is pointing, so you can put it back in the same place. Don't turn the engine after removing the dist. Find a socket...
Forum: 1947 and Older Ford Trucks 10-05-2015, 07:31 AM
Replies: 7
Views: 344
Posted By f5fordgirl
I had the same problems with my 49 F-5, I took...

I had the same problems with my 49 F-5, I took the shoes to napa, they sent them someplace to be relined. They came back looking like new, and were glued. My wheel cyl's were good, and napa got the...
Showing results 1 to 15 of 499

 
Forum Jump
 


All times are GMT -5. The time now is 08:35 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup