Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 25
Search took 0.26 seconds.
Search: Posts Made By: noal133
Forum: Ranger & B-Series 05-11-2015, 10:30 AM
Replies: 7
Views: 250
Posted By noal133
Thats a good article, thank you. After seeing...

Thats a good article, thank you. After seeing that it looks more likely to find a coil spring model, I think that will be what i will start searching for. Thanks to everyone that took the time to...
Forum: Ranger & B-Series 05-11-2015, 09:12 AM
Replies: 7
Views: 250
Posted By noal133
The 1950 is 114" according to some info I...

The 1950 is 114" according to some info I found.The closest ranger I found was a standard cab long bed at 117", so i could work with that. If Im reading correctly there were torsion bar suspension...
Forum: Ranger & B-Series 05-10-2015, 08:21 AM
Replies: 7
Views: 250
Posted By noal133
Thank you for that article. There is a lot of...

Thank you for that article. There is a lot of info there but not quite what I'm looking for. Im thinking super cab frame for the wheel base. I think the later frames would have better front...
Forum: Ranger & B-Series 05-09-2015, 05:48 PM
Replies: 7
Views: 250
Posted By noal133
What are the best years for a donor frame for my project?

Hi, guys and girls . This isn't usually where I hang out but i have a ranger question you. I have a 1950 Ford F1 cab and frond clip that I have been playing with for many years. I have had it on...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-13-2015, 01:04 PM
Replies: 20
Views: 816
Posted By noal133
Its hard to see exactly where now, but it looks...

Its hard to see exactly where now, but it looks like I cut about 1/2 inch behind the edge of the hole. You should be able to lay it out on your frame before you cut. The rear cut on the driver side...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-12-2015, 05:08 PM
Replies: 20
Views: 816
Posted By noal133
That is where i cut mine, just behind the first...

That is where i cut mine, just behind the first set of bed bolts. A short bed bolted right on.
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-18-2015, 07:16 PM
Replies: 16,231
Views: 551,344
Posted By noal133
I did a 3G swap on my 86 F250 using the great...

I did a 3G swap on my 86 F250 using the great info found on this site. Junkyard parts except for a few terminal ends . Less than $25 total.
Forum: 1973 - 1979 F-100 & Larger F-Series Trucks 09-06-2012, 10:22 AM
Replies: 273
Views: 167,598
Posted By noal133
I have enjoyed this thread right from the start!...

I have enjoyed this thread right from the start! Your truck looks great, and you do nice work. If it's not too much trouble could you give a measurement of your width ,outside of tire to out side of...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 08-31-2012, 08:38 AM
Replies: 26
Views: 994
Posted By noal133
What is the flaw you are referring to ?

What is the flaw you are referring to ?
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 05-21-2012, 06:53 PM
Replies: 14
Views: 431
Posted By noal133
I did not talk to him , but we did walk around...

I did not talk to him , but we did walk around the truck a few times admiring it. Very nice. Happy for you!
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 05-21-2012, 06:44 PM
Replies: 14
Views: 431
Posted By noal133
:-X06 I also saw that truck at Spring Carlisle,...

:-X06 I also saw that truck at Spring Carlisle, It looks just as nice in person as it does in the pics.
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 05-08-2012, 08:01 AM
Replies: 7
Views: 495
Posted By noal133
I found this on Wikipedia, " The block was fitted...

I found this on Wikipedia, " The block was fitted with revised, taller lifter bosses to accept roller lifters, and a steel camshaft in 1985"
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-11-2012, 01:23 PM
Replies: 2
Views: 270
Posted By noal133
On the Walker exhaust website the only one I can...

On the Walker exhaust website the only one I can find is listed for E4OD. I would assume it also fits c6. The best price I found was advance auto parts. Using the promo code Visa you could get the...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-11-2012, 12:29 PM
Replies: 5
Views: 935
Posted By noal133
The summit (Pacesetters) are very good quality, I...

The summit (Pacesetters) are very good quality, I also have them.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-09-2012, 07:52 PM
Replies: 9
Views: 1,915
Posted By noal133
I used a walker h-pipe for a heavy duty f250. (...

I used a walker h-pipe for a heavy duty f250. ( pn 40585 for e4od trans ) or (pn 40572 for others) . The cat is kind of expensive for this application (magna flow 93336) , so i loosely copied the...
Showing results 1 to 15 of 25

 
Forum Jump
 


All times are GMT -5. The time now is 09:59 AM.

 

Powered by vBulletin® Version 3.8.7 AC2
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup