Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 499
Search took 0.70 seconds.
Search: Posts Made By: steve(ill)
Forum: 1997 - 2003 F150 Yesterday, 09:33 PM
Replies: 5
Views: 99
Posted By steve(ill)
Ya never know with 240K miles ........ look at...

Ya never know with 240K miles ........ look at my list below. I had a 2001 with that many miles and was having a few problems... what to do ... ? Then it hit a tree on an icy road on day and that...
Forum: 1997 - 2003 F150 Yesterday, 08:17 PM
Replies: 5
Views: 99
Posted By steve(ill)
Ford 5.4 Engine | Rebuilt 5.4 Ford Engine -...

Ford 5.4 Engine | Rebuilt 5.4 Ford Engine - Accurate Engines (http://accurateengines.com/remanufactured-engines/ford/54-engine/)
Forum: 1997 - 2003 F150 Yesterday, 08:14 PM
Replies: 5
Views: 99
Posted By steve(ill)
2001 Ford F150 5 4L Engine Motor 143K | eBay

2001 Ford F150 5 4L Engine Motor 143K | eBay
Forum: 1997 - 2003 F150 Yesterday, 08:12 PM
Replies: 5
Views: 99
Posted By steve(ill)
a lot depends on the location and you can use low...

a lot depends on the location and you can use low mile replacements from the scrap yard, or rebuild at local shop. $2000 - $2500 for each would be close. I would check a local transmission or motor...
Forum: 1997 - 2003 F150 Yesterday, 08:04 PM
Replies: 5
Views: 96
Posted By steve(ill)
Without the switch, is it possible to be...

Without the switch, is it possible to be something else ?

Possible Causes of code 27

A PAD warning lamp...
Forum: 1997 - 2003 F150 Yesterday, 07:59 PM
Replies: 5
Views: 84
Posted By steve(ill)
I was thinking the same thing... The 1/4 inch...

I was thinking the same thing... The 1/4 inch smaller is probably about 10%.. If you are on the road most of the time, running 1400- 2000 RPM you should be OK. If you spend a lot of time at idle with...
Forum: 1997 - 2003 F150 Yesterday, 07:55 PM
Replies: 3
Views: 73
Posted By steve(ill)
Its nice to be on the winning side now and then,...

Its nice to be on the winning side now and then, aint it !!
Forum: 1997 - 2003 F150 Yesterday, 07:51 PM
Replies: 40
Views: 636
Posted By steve(ill)
If its the outside 3 threads and the rest looks...

If its the outside 3 threads and the rest looks good... the old trick is to take a small grinder or file and just wipe off the bad area. The nut will go past that and the last 2-3 threads don't do...
Forum: 1997 - 2003 F150 09-02-2015, 08:41 PM
Replies: 40
Views: 636
Posted By steve(ill)
make sure those two sliding pins move in and out...

make sure those two sliding pins move in and out real easy in the caliper mount. Sometimes I have to sandpaper the dowels and spray penetrant / cleaner / ect in the holes to get a good slide.
Forum: 1997 - 2003 F150 09-02-2015, 06:08 PM
Replies: 5
Views: 96
Posted By steve(ill)
several options, read down a few posts Air...

several options, read down a few posts

Air Bag Code 27 Update - F150online Forums (http://www.f150online.com/forums/lightning/208842-air-bag-code-27-update.html)
Forum: 1997 - 2003 F150 09-02-2015, 06:03 PM
Replies: 4
Views: 50
Posted By steve(ill)
the wires are suppose to go to a brake...

the wires are suppose to go to a brake controller........... you need to follow the wires and see where it is located......... no other use for the wires.
Forum: 1997 - 2003 F150 09-01-2015, 09:34 PM
Replies: 3
Views: 160
Posted By steve(ill)
yea, I have considered that. Looks like it would...

yea, I have considered that. Looks like it would stick down a little lower than I would like.. but it is a thought.

I have also considered "modifying" the factory bumper to have a step. I don't...
Forum: 1997 - 2003 F150 08-31-2015, 06:02 PM
Replies: 40
Views: 636
Posted By steve(ill)
I have a bench grinder with a wire wheel and I...

I have a bench grinder with a wire wheel and I use it on any parts that I can move. For inplace parts, I have a 3 inch wire wheel on a hand grinder..... as you said, stay away from the rubber. Make...
Forum: 1997 - 2003 F150 08-31-2015, 03:58 PM
Replies: 4
Views: 159
Posted By steve(ill)
check the frame area under the bed, above the...

check the frame area under the bed, above the rear axle area. Tires seem to throw salt in that area if you live in that environment. Couple trucks on this site have had holes rot thru the frame......
Forum: 1997 - 2003 F150 08-30-2015, 05:35 PM
Replies: 8
Views: 282
Posted By steve(ill)
They could be right.. That being said, I have had...

They could be right.. That being said, I have had keys go bad... also son had a Taurus that the key would not signal the coil and it would not start... Im no expert here but basically I think there...
Showing results 1 to 15 of 499

 
Forum Jump
 


All times are GMT -5. The time now is 01:10 AM.

 

Powered by vBulletin® Version 3.8.7 AC2
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup