Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 312
Search took 0.08 seconds.
Search: Posts Made By: gerrymoe
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-31-2015, 03:18 PM
Replies: 9
Views: 264
Posted By gerrymoe
Sigh of relief overcomes ya than reality of how...

Sigh of relief overcomes ya than reality of how stupid I feel sets in
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-30-2015, 08:02 PM
Replies: 3
Views: 119
Posted By gerrymoe
There are two mounts that penetrate thru the...

There are two mounts that penetrate thru the floor than thru an angle attached to the running board brackets. If he has the two rear running board brackets he is golden, he also can remove the...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-28-2015, 11:04 AM
Replies: 23
Views: 852
Posted By gerrymoe
Sometime lessons are learned the hard way and...

Sometime lessons are learned the hard way and that is not necessarily bad. If this situation was in my hands I would do just as you have done sought advice and than process into an appropriate...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-27-2015, 10:44 AM
Replies: 11
Views: 486
Posted By gerrymoe
I believe once the panel is sold to the...

I believe once the panel is sold to the dismantler, it can only be sold back as a salvage which means there will be some hoops to jump thru to get it back on the road, which could run into more than...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-26-2015, 11:58 PM
Replies: 15
Views: 401
Posted By gerrymoe
Paul I live in Madera CA approx 50-60 miles...

Paul

I live in Madera CA approx 50-60 miles from Visalia. I would be more than willing to drive down and see if I could be of assistance to you at no charge. I have fabbed a few sets of motor...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-16-2015, 11:13 AM
Replies: 26
Views: 757
Posted By gerrymoe
Quit spending so much time imagining the finished...

Quit spending so much time imagining the finished product and spend time on the steps that lead to the finished product. Within that period things will change, financial situation, a more positive...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-06-2015, 10:46 AM
Replies: 21
Views: 535
Posted By gerrymoe
My first post try I only posted "Nailed it" and...

My first post try I only posted "Nailed it" and the site came back and said post to small
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-06-2015, 10:40 AM
Replies: 21
Views: 535
Posted By gerrymoe
Nailed it!!! Have to say more site won't allow...

Nailed it!!! Have to say more site won't allow two words only. Sweeeeet!!

Bluey

2" down in the rear,,, 3" down in the front
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-04-2015, 08:42 PM
Replies: 34
Views: 1,817
Posted By gerrymoe
That is a great idea and if ya don't mind I think...

That is a great idea and if ya don't mind I think I will use that idea. Thanx for that picture you gave me a big motivation lift. I have been dwelling on this problem for quite awhile. Do those have...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-04-2015, 08:38 PM
Replies: 34
Views: 1,817
Posted By gerrymoe
Not a 100%, I do measurements across the two...

Not a 100%, I do measurements across the two hoods I have and they are smaller by a strong 1/8. When I put the slides on for the front tilt hood the passenger side does not seat. Did not have this...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-04-2015, 08:27 PM
Replies: 34
Views: 1,817
Posted By gerrymoe
Here is my idea to get the 3/16 difference on the...

Here is my idea to get the 3/16 difference on the passenger side handled. I got a very strong 1/8 by tightening, letting loose than again until I could get no more. I will now put the front clip...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-04-2015, 08:22 PM
Replies: 34
Views: 1,817
Posted By gerrymoe
Earlier I had mentioned my passenger side running...

Earlier I had mentioned my passenger side running board was in need of attention. Well after about 20 hours of massaging I got it to a respectable point. Going to shoot some shiny on it and see.
...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-04-2015, 08:19 PM
Replies: 34
Views: 1,817
Posted By gerrymoe
Got some more welding done on the firewall and...

Got some more welding done on the firewall and primed. Also I have installed the fatman 2" lowering spindles. I am installing the 1 1/8 sway bar but had to take it in and get it rebent a little.
...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-04-2015, 08:15 PM
Replies: 34
Views: 1,817
Posted By gerrymoe
Just an update om where I am at. Finally got a...

Just an update om where I am at. Finally got a hood. I tried the fit and had issues. Mainly gaps, got quite a bit taken care of but to get more I had to take the front clip off, so I took care of a...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-01-2015, 11:31 PM
Replies: 15
Views: 528
Posted By gerrymoe
I am thinking the new brake drum center hole that...

I am thinking the new brake drum center hole that slides over the axle is smaller than the original and the brake drum is not flush against the axle hub or the drum is hitting the backing plate not...
Showing results 1 to 15 of 312

 
Forum Jump
 


All times are GMT -5. The time now is 02:06 AM.

 

Powered by vBulletin® Version 3.8.7 AC2
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup