Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 497
Search took 0.59 seconds.
Search: Posts Made By: TexasRebel
Forum: Super Duty & Heavy Duty 08-21-2015, 10:54 AM
Replies: 5
Views: 325
Posted By TexasRebel
Also... clean what? it is literally...

Also...

clean what?

it is literally nothing more than a butterfly valve in cast aluminum, a position sensor, and a rotary actuator...

Are you thinking Throttle Body Injection (TBI)? These...
Forum: Super Duty & Heavy Duty 08-21-2015, 10:40 AM
Replies: 2
Views: 180
Posted By TexasRebel
is the chain stretched?

is the chain stretched?
Forum: Super Duty & Heavy Duty 08-20-2015, 11:04 AM
Replies: 5
Views: 325
Posted By TexasRebel
Because it's likely caused by bad data coming...

Because it's likely caused by bad data coming from the throttle position sensor. Eight years of hot/cold cycles will wear a sensor out. The TPS is part of the throttle body, and not the easiest...
Forum: Super Duty & Heavy Duty 08-19-2015, 06:27 PM
Replies: 16
Views: 1,026
Posted By TexasRebel
yeah? Around here every third pickup is a...

yeah?

Around here every third pickup is a Super Duty...

Attracting women? Not so much... Hauling a motorcycle out of the plains? No problem.
Forum: Super Duty & Heavy Duty 08-19-2015, 06:21 PM
Replies: 5
Views: 325
Posted By TexasRebel
Big wrench lit up my display...

On Southbound I35W just north of Ft. Worth at the 820 interchange which is under just a bit of construction...

I slow down for traffic, and everything just starts rattling! I see this wrench on...
Forum: Super Duty & Heavy Duty 08-11-2015, 12:45 PM
Replies: 2
Views: 272
Posted By TexasRebel
If the angles turn out right you will eliminate...

If the angles turn out right you will eliminate the inherent surging that comes with a 2-piece drive shaft having an odd number of u-joints (it is impossible to phase 3 u-joints). If the angles...
Forum: Super Duty & Heavy Duty 08-07-2015, 05:22 PM
Replies: 4
Views: 248
Posted By TexasRebel
It's pretty easy to swap those for the composite...

It's pretty easy to swap those for the composite headlights in the XLT package...

The only reason I haven't is price...
Forum: Conventional (Bumper Pull) Towing; Travel Trailers, Pop-ups & Slide-in Campers 08-05-2015, 05:31 PM
Replies: 127
Views: 6,041
Posted By TexasRebel
is that crack in the fitting boss or just some...

is that crack in the fitting boss or just some grout around it?
Forum: Super Duty & Heavy Duty 08-05-2015, 05:22 PM
Replies: 14
Views: 553
Posted By TexasRebel
Are you not curious what is shorting? Seems like...

Are you not curious what is shorting? Seems like an electrical gremlin in the making.
Forum: Super Duty & Heavy Duty 08-05-2015, 05:21 PM
Replies: 14
Views: 553
Posted By TexasRebel
Lights on the running boards? Is that an...

Lights on the running boards? Is that an aftermarket effect, or stock?
When are the running board lights on? Could they be backfeeding into the headlights?

Actually, it's not the headlights,...
Forum: Super Duty & Heavy Duty 08-01-2015, 06:43 PM
Replies: 14
Views: 553
Posted By TexasRebel
either take the key out or turn the lights off.

either take the key out or turn the lights off.
Forum: Super Duty & Heavy Duty 07-24-2015, 05:10 PM
Replies: 34
Views: 1,019
Posted By TexasRebel
Could be clutches slipping. Goes away in low...

Could be clutches slipping. Goes away in low because the torque requirement is reduced.

how many miles on the transmission?
Forum: Super Duty & Heavy Duty 07-22-2015, 10:26 PM
Replies: 34
Views: 1,019
Posted By TexasRebel
you have a 2wd low?

you have a 2wd low?
Forum: Super Duty & Heavy Duty 07-20-2015, 09:00 PM
Replies: 31
Views: 1,331
Posted By TexasRebel
sounds like the starter may be drawing the...

sounds like the starter may be drawing the battery down enough to erase the memory on the radio. Especially if it is an 11 with an original battery.

Why radios cannot use non-volatile memory for...
Forum: Super Duty & Heavy Duty 07-20-2015, 08:55 PM
Replies: 34
Views: 1,019
Posted By TexasRebel
Are you certain the front output shaft is engaged...

Are you certain the front output shaft is engaged in 4H?

the shift pattern is 4L-N-2-4H

If the linkage (I'm assuming floor shift here) is set too far one way, the transfer case may be between...
Showing results 1 to 15 of 497

 
Forum Jump
 


All times are GMT -5. The time now is 04:18 PM.

 

Powered by vBulletin® Version 3.8.7 AC2
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup