Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 498
Search took 1.04 seconds.
Search: Posts Made By: HOTWRENCH
Forum: Large Truck 05-24-2015, 08:16 AM
Replies: 8
Views: 300
Posted By HOTWRENCH
Talking AIR GOVENOR

A D2 later style governor can be retrofitted , some are mounted on the compressor but can be mounted remotely. These can be found at truck shops and can be bought at NAPA.


Have A...
Forum: Large Truck 05-11-2015, 03:48 PM
Replies: 2
Views: 311
Posted By HOTWRENCH
Talking Starter Problems

I had a 81 F700 with a 429 it too had starter issues. NAPA sells two different starter drives that will fit that starter one is a 9 tooth version the other is a 10 tooth drive. The 10 tooth is...
Forum: Large Truck 04-30-2015, 08:01 AM
Replies: 13
Views: 480
Posted By HOTWRENCH
Talking FT vs FE

}>As far as swapping distributors between FE/FT here's how it goes . A FE distributor has a 1/4 in oil pump drive, the FT has a 5/16inch oil pump drive.
So to use a FE dist in a FT you must install...
Forum: Large Truck 12-22-2014, 03:09 PM
Replies: 17
Views: 885
Posted By HOTWRENCH
FT's

I understand what your books tell you , but there are lots of half breed combinations out there. I've seen and built many half breeds so the customer has a running truck. I've also took a 330MD and...
Forum: Large Truck 12-21-2014, 01:03 PM
Replies: 17
Views: 885
Posted By HOTWRENCH
FT differences

If you have a small crank FT it can be one of several variations. What exhaust manifold are used on this engine? If they are similar to pickup style with no center exhaust port, they are the same as...
Forum: 1957 - 1960 F100 & Larger F-Series Trucks 08-18-2014, 06:17 AM
Replies: 6
Views: 897
Posted By HOTWRENCH
Talking Brake Upgrade

Converting your truck to disc brakes is a easy job. The internet is your friend , look up 9in brake conversions and the same for the front axle. Ther are companys tha sell kits just for this purpose....
Forum: 1957 - 1960 F100 & Larger F-Series Trucks 06-13-2014, 06:19 AM
Replies: 4
Views: 545
Posted By HOTWRENCH
Talking Fire Truck

I have a 57 F600 that had a Y block when built, I installed a FE 390 . It is an easy swap and works very well, if you want a FT will fit just as well. I have installed both styles over the years and...
Forum: Large Truck 05-01-2014, 07:13 AM
Replies: 28
Views: 1,470
Posted By HOTWRENCH
Talking FE's and FT"S

If you are rebuilding that 390 that you are installing -- consider this upgrade to FT specs in regard to pistons /compression ratio / change to FT heads intake and exhaust manifolds. This would give...
Forum: Large Truck 12-31-2013, 06:45 AM
Replies: 4
Views: 436
Posted By HOTWRENCH
Talking Engine Interchange

You can install the 292 in the newer frame if you have the complete Y block setup complete from front mt to bellhousing assembly. If you want to use a 390 you will need the FT bell and a flywheel...
Forum: Large Truck 11-29-2013, 07:31 AM
Replies: 11
Views: 850
Posted By HOTWRENCH
Talking PARTS

Try Cresson Ridge Diesel Garage in Cresson Pa. Phone # 814-886-4164. They rebuild transmissions and rears and have a large inventory of new and used parts. I have dealt with them for years and they...
Forum: Large Truck 11-25-2013, 07:40 AM
Replies: 24
Views: 1,573
Posted By HOTWRENCH
Talking No Start

Check the plug that fits in the back of the ignition switch, they corrode and can cause this problem, sometimes the wires will be burnt back and the terminals will be blackened and melted. There is...
Forum: Large Truck 11-25-2013, 07:23 AM
Replies: 10
Views: 2,243
Posted By HOTWRENCH
BRAKES

Just a tip the brakes must first be adjusted to be able too bleed the system and get repeatable results. Bleeding an out of adjustment brakes will give eratic results and cause a multitude of odd...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 10-07-2013, 05:21 PM
Replies: 4
Views: 449
Posted By HOTWRENCH
Parts Help

I am looking for some parts for a 55 Ford 3spd overdrive transmission, new or used it makes no difference to me. What I am looking for is the speedometer drive gear that is on the output shaft. The...
Forum: FE & FT Big Block V8 (332, 352, 360, 390, 406, 410, 427, 428) 09-25-2013, 04:57 PM
Replies: 15
Views: 1,970
Posted By HOTWRENCH
Talking Mufflers

I have been useing Jones Full Boar mufflers and Thrush glasspacks, the Jones have a nice mellow tone till you step on it , sounds great and no drone at cruise speed. I like to use the longest Thrush...
Forum: FE & FT Big Block V8 (332, 352, 360, 390, 406, 410, 427, 428) 07-24-2013, 06:03 AM
Replies: 27
Views: 7,312
Posted By HOTWRENCH
Talking Ignition

6 to 9 volts is the norm , swap the coil out it sounds like its failing when it gets hot}>

Have A Good Day ------- Hotwrench}>
Showing results 1 to 15 of 498

 
Forum Jump
 


All times are GMT -5. The time now is 02:31 PM.

 

Powered by vBulletin® Version 3.8.7 AC2
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup