Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 500
Search took 0.27 seconds.
Search: Posts Made By: Phy
Forum: 1987 - 1996 F150 & Larger F-Series Trucks Yesterday, 11:54 AM
Replies: 4
Views: 182
Posted By Phy
It depends on if it's a dually pickup, F350 Cab &...

It depends on if it's a dually pickup, F350 Cab & Chassis, or F-Super Duty. They are all different widths.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 05-16-2015, 09:55 AM
Replies: 4
Views: 164
Posted By Phy
Yes, if the ignition was bad, it should still...

Yes, if the ignition was bad, it should still turn over by jumping the starter relay on the fender.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 05-13-2015, 09:21 PM
Replies: 1
Views: 128
Posted By Phy
Does it start, quickly die, then crank a lot then...

Does it start, quickly die, then crank a lot then start and run? That's air intrusion in the fuel system.
Post in the IDI forum and you'll get more response...
Pre-Power Stroke Diesel (7.3L IDI &...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 05-12-2015, 08:59 AM
Replies: 4
Views: 146
Posted By Phy
Consider it confirmed.

Consider it confirmed.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 05-10-2015, 05:02 PM
Replies: 8
Views: 439
Posted By Phy
If you get a used one, look at the wires...

If you get a used one, look at the wires carefully where they exit the lever at the column...
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 05-09-2015, 03:16 PM
Replies: 8
Views: 162
Posted By Phy
Great idea, Tom!

Great idea, Tom!
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 05-06-2015, 11:45 AM
Replies: 23
Views: 554
Posted By Phy
I'd check to see if the starter relay on the...

I'd check to see if the starter relay on the fender is getting a signal from the ignition switch when the key is turned to start. Pull the small wire off the small terminal on the relay and check...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 05-01-2015, 05:54 PM
Replies: 12
Views: 255
Posted By Phy
It'd be tough. If it has good compression, a...

It'd be tough. If it has good compression, a good IP, good injectors, no fuel system air intrusion, a fast starter, and great batteries & cables, you'd probably be OK.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-26-2015, 12:20 PM
Replies: 25
Views: 35,772
Posted By Phy
Your '93 is different than those instructions. ...

Your '93 is different than those instructions. Send me your email and I'll send you a pdf with instructions.

Phy
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-26-2015, 12:12 PM
Replies: 7
Views: 244
Posted By Phy
Looks like it's a '92. Does everything else...

Looks like it's a '92.
Does everything else with the key work, other than the starter? If so, I'd be looking at the NSS or clutch interlink...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-22-2015, 08:38 AM
Replies: 6
Views: 224
Posted By Phy
If the tick gets louder with throttle, it's...

If the tick gets louder with throttle, it's exhaust. If not, it's something else...
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 04-22-2015, 08:31 AM
Replies: 5
Views: 218
Posted By Phy
Your '92 IDI doesn't need a pcm (eec, teca,...

Your '92 IDI doesn't need a pcm (eec, teca, computer) for the engine, but it does have one for the trans, and it is OBD1. The connector is under the hood on the inner fender near the drivers side...
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 04-20-2015, 06:52 PM
Replies: 16
Views: 454
Posted By Phy
My '94 F-Super takes type-F atf.

My '94 F-Super takes type-F atf.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-20-2015, 08:49 AM
Replies: 3
Views: 161
Posted By Phy
No, the temp knob moves an air door, the "blend"...

No, the temp knob moves an air door, the "blend" door, to either route air through the heater core or bypass it. Coolant is flowing through the heater core anytime the engine is running. The heater...
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 04-19-2015, 06:28 PM
Replies: 7
Views: 198
Posted By Phy
The carrier is very tight in the housing to get...

The carrier is very tight in the housing to get bearing preload. You're supposed to use a case spreader to relieve the pressure:
...
Showing results 1 to 15 of 500

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 05:32 AM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup