Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 498
Search took 0.76 seconds.
Search: Posts Made By: greystreak92
Forum: 1978 - 1996 Big Bronco Yesterday, 01:34 PM
Replies: 2
Views: 84
Posted By greystreak92
Water in the distributor? Check for a cracked...

Water in the distributor? Check for a cracked cap. Water in the ICM connection. Water in the alternator. There are a host of possibilities.
Forum: 1978 - 1996 Big Bronco 05-24-2015, 11:35 PM
Replies: 1
Views: 34
Posted By greystreak92
Have you tried heating it up? There is a good...

Have you tried heating it up? There is a good possibility it will be more acquiescent to removal with the manifold at operating temperature. Otherwise, without removing the manifold you are...
Forum: 1978 - 1996 Big Bronco 05-24-2015, 11:29 PM
Replies: 2
Views: 94
Posted By greystreak92
Deleting all that will do wonders for it... NOT. ...

Deleting all that will do wonders for it... NOT. Especially considering that in spite of the fact that the basic engine is the same as it was in 1990, the entire control system for the 96 engine is...
Forum: 1978 - 1996 Big Bronco 05-20-2015, 08:59 PM
Replies: 2
Views: 75
Posted By greystreak92
Yes. The columns didn't change after 92 AFAIK. ...

Yes. The columns didn't change after 92 AFAIK. Some of the internals and wiring did when the airbags were added though.
Forum: 1978 - 1996 Big Bronco 05-18-2015, 12:48 AM
Replies: 15
Views: 306
Posted By greystreak92
The EVP sensor is a variable resistance device. ...

The EVP sensor is a variable resistance device. It moves with the EGR valve. The valve opens when vacuum is applied and closes when vacuum is removed. The resistance value of the EVP sensor...
Forum: 1978 - 1996 Big Bronco 05-16-2015, 08:07 PM
Replies: 15
Views: 306
Posted By greystreak92
Profile Ignition Pickup is a hall-effect...

Profile Ignition Pickup is a hall-effect inductive sensor under the distributor rotor that effectively replaces the mechanical breaker points that preceded it in older models. The Stator for the PIP...
Forum: 1978 - 1996 Big Bronco 05-16-2015, 10:43 AM
Replies: 15
Views: 306
Posted By greystreak92
EGR uses an EVP sensor rather than a PFE sensor. ...

EGR uses an EVP sensor rather than a PFE sensor. But if you ordered for the truck/engine in question, that's what you should end up with.
Forum: 1978 - 1996 Big Bronco 05-16-2015, 08:58 AM
Replies: 15
Views: 306
Posted By greystreak92
I'm with Kem on the idea of an exhaust leak...

I'm with Kem on the idea of an exhaust leak upstream of the O2 sensor. Any HEGO more than five years old should be replaced. Their ability to continue to generate voltage deteriorates rapidly after...
Forum: 1978 - 1996 Big Bronco 05-14-2015, 03:44 PM
Replies: 15
Views: 306
Posted By greystreak92
So the pinging and such continues and the knock...

So the pinging and such continues and the knock sensor is working?
ACT readings correspond to infrared as well?
Fault Codes present or recurring during KOER are?
Forum: 1978 - 1996 Big Bronco 05-14-2015, 03:18 PM
Replies: 5
Views: 143
Posted By greystreak92
The common incorrect fix for a dead or dying IAC...

The common incorrect fix for a dead or dying IAC is to run the screw in enough that it holds the throttle butterflies open a bit. While this works to keep the truck from dying until the IAC can be...
Forum: 1978 - 1996 Big Bronco 05-14-2015, 02:58 PM
Replies: 4
Views: 132
Posted By greystreak92
Check booster vacuum?

Check booster vacuum?
Forum: 1978 - 1996 Big Bronco 05-11-2015, 11:09 PM
Replies: 5
Views: 150
Posted By greystreak92
Interlock switch in the driver's side latch is...

Interlock switch in the driver's side latch is the most likely culprit. if it doesn't fully latch, the interlock switch won't engage and the window won't move in either direction once it is all the...
Forum: 1978 - 1996 Big Bronco 05-11-2015, 10:57 PM
Replies: 5
Views: 143
Posted By greystreak92
Have you checked to be certain that the throttle...

Have you checked to be certain that the throttle plate stop screw has not been tampered with? The RPM's you are talking about sound a touch on the high side for normal idle. There is a method for...
Forum: 1978 - 1996 Big Bronco 05-09-2015, 10:27 AM
Replies: 2
Views: 123
Posted By greystreak92
Most likely you won't find much of the wiring for...

Most likely you won't find much of the wiring for the door electronics if the power windows and locks were not original to the truck. However, if you go looking for a donor truck, you can pull the...
Forum: 1978 - 1996 Big Bronco 05-04-2015, 11:29 PM
Replies: 8
Views: 159
Posted By greystreak92
DO NOT attempt this kind of wiring modification! ...

DO NOT attempt this kind of wiring modification! Neither the wiring nor the internal circuit breaker in the headlamp switch are capable of handling the load of all four filaments (two per lamp) at...
Showing results 1 to 15 of 498

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 11:26 AM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup