Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 498
Search took 0.36 seconds.
Search: Posts Made By: 38 coupe
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 04:26 PM
Replies: 3
Views: 115
Posted By 38 coupe
My PDF 48-56 parts catalog only shows the later...

My PDF 48-56 parts catalog only shows the later part number B5AZ-10505-A for a 48-51 truck regulator. I packed up all my paper catalogs which would have given you an accurate answer. Hopefully...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 04:18 PM
Replies: 56
Views: 1,549
Posted By 38 coupe
That sure looks like a two speed axle from a...

That sure looks like a two speed axle from a larger truck. Interesting. Most of those were geared for slow and slower.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 04:09 PM
Replies: 2
Views: 135
Posted By 38 coupe
If anyone goes I would love to see pictures.

If anyone goes I would love to see pictures.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 04:07 PM
Replies: 13
Views: 314
Posted By 38 coupe
I ran 6V halogen headlights and LED tail lights...

I ran 6V halogen headlights and LED tail lights with a 6V generator on my 37 sedan. You can get or build a 6V positive ground to 12V negative ground inverter for in car uses.

If you think you...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 04:03 PM
Replies: 116
Views: 6,233
Posted By 38 coupe
I hope you get feeling better.

I hope you get feeling better.
Forum: 1947 and Older Ford Trucks 05-21-2015, 07:36 PM
Replies: 10
Views: 226
Posted By 38 coupe
Your heads likely do have the part numbers cast...

Your heads likely do have the part numbers cast in, just not where it is easy to see. 9T is the correct marking for 239 Truck heads. Ford stopped marking the entire part number on the visible face of...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-21-2015, 07:28 PM
Replies: 11
Views: 311
Posted By 38 coupe
Welcome! Your truck looks very nice. I wouldn't...

Welcome! Your truck looks very nice. I wouldn't change it too much.

You may have a 4.27 ratio rear axle. That and a four speed crash box make a really slow shifting, slow cruising truck. The...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-21-2015, 07:10 PM
Replies: 53
Views: 1,893
Posted By 38 coupe
Ford had no adjustment other than pinion bearing...

Ford had no adjustment other than pinion bearing pre-load. The champ quick change guys, who your gears were made for, do have adjustments. The shim the carrier bearings on the carrier, they shim the...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-21-2015, 07:03 PM
Replies: 51
Views: 1,227
Posted By 38 coupe
I have adjusted the valves on a 226 in a 1950...

I have adjusted the valves on a 226 in a 1950 sedan. I pulled the passenger front wheel, the inner fender access plate, the inspection covers, and adjusted away. I wouldn't say it was fun, but it...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-21-2015, 06:57 PM
Replies: 13
Views: 314
Posted By 38 coupe
The best method to do this is to use two...

The best method to do this is to use two generators, one 6V and one 12V. Take the pulley and the ends from the flathead 6V generator. Use the armature and barrel from the 12V generator. You now have...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-21-2015, 06:52 PM
Replies: 3
Views: 109
Posted By 38 coupe
When I rebuilt my 215 I found a second block...

When I rebuilt my 215 I found a second block since the first block was already at 223 standard and needed another bore. The engine didn't run hot and probably would have been fine, I just preferred...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-20-2015, 05:02 PM
Replies: 53
Views: 1,893
Posted By 38 coupe
Here is another thread where a 4.11 set was...

Here is another thread where a 4.11 set was installed, maybe it will give you some ideas: http://www.ford-trucks.com/forums/1280661-chucks-trucks-4-11-conversion.html
Forum: 1947 and Older Ford Trucks 05-20-2015, 04:57 PM
Replies: 10
Views: 226
Posted By 38 coupe
Technically 81A is correct only for 221 cubic...

Technically 81A is correct only for 221 cubic inch engines. 99 is the designation for pre-war 239 motors. For anyone really wanting to learn flathead engine blocks, please read this thread from the...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-20-2015, 04:45 PM
Replies: 3
Views: 109
Posted By 38 coupe
The only new pistons I am aware of are from Egge....

The only new pistons I am aware of are from Egge. Egge is expensive. I lucked out and found a NOS set of 30 over pistons when I was going through my motor. I watched ebay, Ford Barn, and the HAMB. I...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-20-2015, 04:40 PM
Replies: 41
Views: 2,117
Posted By 38 coupe
Looking good. Try to do one thing each day. That...

Looking good. Try to do one thing each day. That helps keep you interested, and also helps give that important feeling of accomplishment.
Showing results 1 to 15 of 498

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 01:28 AM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup