Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 499
Search took 0.24 seconds.
Search: Posts Made By: f5fordgirl
Forum: Ranger & B-Series Today, 11:05 AM
Replies: 3
Views: 97
Posted By f5fordgirl
Can't tell about the runaway rpm's,, unless you...

Can't tell about the runaway rpm's,, unless you have a sticky throttle cable. Are you loosing coolant from the over flow tank, if so, you could have a bad head gasket. Not bad enough to burn coolant,...
Forum: Ranger & B-Series 05-02-2015, 07:57 PM
Replies: 1
Views: 83
Posted By f5fordgirl
If its not low on fluid, the tc may have went bad.

If its not low on fluid, the tc may have went bad.
Forum: 1961 - 1966 F-100 & Larger F-Series Trucks 05-02-2015, 11:54 AM
Replies: 2
Views: 127
Posted By f5fordgirl
If you have a pair of pliers, you could squeeze...

If you have a pair of pliers, you could squeeze the end of the wire where it goes over the plug a little, making it fit tighter. as for the exhaust popping, the carb may be too rich causing the...
Forum: 1957 - 1960 F100 & Larger F-Series Trucks 05-01-2015, 06:55 AM
Replies: 8
Views: 158
Posted By f5fordgirl
I heard my uncle say that a 262 had timing gears...

I heard my uncle say that a 262 had timing gears instead of a chain,.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 04-25-2015, 05:39 PM
Replies: 7
Views: 229
Posted By f5fordgirl
I think he's talking about the cotter pins that...

I think he's talking about the cotter pins that hold the linkage onto the shift arms on the outside of the cover.
Forum: 1947 and Older Ford Trucks 04-24-2015, 07:27 AM
Replies: 2
Views: 232
Posted By f5fordgirl
If the key is broken off, use a good flat blade...

If the key is broken off, use a good flat blade screwdriver and some penetrating spray, and you should be able to turn it.
Forum: 1961 - 1966 F-100 & Larger F-Series Trucks 04-24-2015, 06:47 AM
Replies: 8
Views: 326
Posted By f5fordgirl
New gaskets may not work for long in stopping the...

New gaskets may not work for long in stopping the leak if the manifold, as well as the head side are really scaled and pitted. You may have to pull the head as well, and have it and the manifold...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 04-22-2015, 06:09 PM
Replies: 7
Views: 229
Posted By f5fordgirl
The homemade rod may be too long, put the shifter...

The homemade rod may be too long, put the shifter and trans in either rev or 1st. Then adjust the rod so it just slips into both shifter, and trans leaver, then work the shifter to N, and see if the...
Forum: 335 Series- 5.8/351M, 6.6/400, 351 Cleveland 04-22-2015, 12:55 PM
Replies: 11
Views: 202
Posted By f5fordgirl
Try turning it with a socket and breaker bar...

Try turning it with a socket and breaker bar backwards, if the bendix is stuck, that will break it loose.
Forum: 335 Series- 5.8/351M, 6.6/400, 351 Cleveland 04-20-2015, 05:33 PM
Replies: 2
Views: 80
Posted By f5fordgirl
Could be a bad starter or solenoid, or a battery...

Could be a bad starter or solenoid, or a battery cable between the solenoid and battery, or a bad ground. And did you jump from the hot lug on the sol, to the s post, or jump from one big post to the...
Forum: Ranger & B-Series 04-13-2015, 12:06 PM
Replies: 6
Views: 182
Posted By f5fordgirl
If you have a dist, you won't have a cam position...

If you have a dist, you won't have a cam position sync, so it could be the pick up coil in the dist, or the coil may be bad
Forum: Ranger & B-Series 04-11-2015, 07:26 PM
Replies: 7
Views: 227
Posted By f5fordgirl
What I ment by overfilling was, maybe adding gas...

What I ment by overfilling was, maybe adding gas from a can you over filled the area where the cap screws on, and he fuel was running down the outside of the fill pipe.
Forum: Ranger & B-Series 04-10-2015, 10:30 AM
Replies: 7
Views: 227
Posted By f5fordgirl
Its fitted to the tank neck with a hose type...

Its fitted to the tank neck with a hose type clamp, but it might not be leaking, the drip may have been from over filling, and was dripping off the lower end. Before you start taking things apart,...
Forum: Bronco II 04-08-2015, 02:16 PM
Replies: 2
Views: 135
Posted By f5fordgirl
You didn't mention miles, but the timing chain...

You didn't mention miles, but the timing chain and gears may have went bad.
Forum: Large Truck 04-07-2015, 03:31 PM
Replies: 8
Views: 236
Posted By f5fordgirl
If you're using the 361 bellhousing, using a 360...

If you're using the 361 bellhousing, using a 360 flywheel isn't going to work. 360 flywheel is much smaller, and the starter bendix won't touch it. Find a light duty 330 flywheel, it will fit the...
Showing results 1 to 15 of 499

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 12:21 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup