Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 500
Search took 0.74 seconds.
Search: Posts Made By: EPNCSU2006
Forum: Engine Swaps 04-17-2015, 09:13 AM
Replies: 8
Views: 152
Posted By EPNCSU2006
The link works ok for me. As for the fuel tables,...

The link works ok for me. As for the fuel tables, think of it this way: the mass air sensor tells the ECU how much air is entering the engine. To achieve the desired fuel mixture, it has a lookup for...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-17-2015, 08:51 AM
Replies: 8
Views: 143
Posted By EPNCSU2006
I rebuilt the ZF in my truck due to the same...

I rebuilt the ZF in my truck due to the same issue. The reverse gear and thrust surface on the mainshaft were very worn, allowing the reverse gear to move far enough from the slider to keep the...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-13-2015, 04:42 AM
Replies: 2
Views: 152
Posted By EPNCSU2006
With both of those lights on, the first thing to...

With both of those lights on, the first thing to check is the float switch in the master cylinder and its connector and wiring.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-08-2015, 05:09 PM
Replies: 2
Views: 164
Posted By EPNCSU2006
My first thought is power steering pressure...

My first thought is power steering pressure switch. Some trucks used one, some did not, but I think most, if not all trucks had the wiring pigtail.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 03-30-2015, 04:46 AM
Replies: 4
Views: 104
Posted By EPNCSU2006
I would connect the hydraulic line to the slave...

I would connect the hydraulic line to the slave instead of trying to bleed anything with the fitting. Open the bleeder, then push the pedal down, close the bleeder and pull the pedal back up. Repeat...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 03-14-2015, 06:27 AM
Replies: 7
Views: 263
Posted By EPNCSU2006
Ford began using in-tank fuel delivery modules...

Ford began using in-tank fuel delivery modules with integral valves in 1990, so there is no external switching valve on the frame rail.
Forum: Performance & General Engine Building 03-11-2015, 04:40 AM
Replies: 7
Views: 134
Posted By EPNCSU2006
The speed sensor in the rear axle should be the...

The speed sensor in the rear axle should be the only speed sensor there is on your truck. If for some reason you have the other, it would be on the tailshaft of the transmission or transfer case...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 03-11-2015, 04:34 AM
Replies: 4
Views: 194
Posted By EPNCSU2006
The master cylinder will be fine, but you'll need...

The master cylinder will be fine, but you'll need to swap the hydraulic line to match up with the concentric slave cylinder used on the ZF. I suggest a new slave cylinder while you can get to it,...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 03-07-2015, 05:21 AM
Replies: 6
Views: 242
Posted By EPNCSU2006
You're right, it will only be accurate in that...

You're right, it will only be accurate in that location when the thermostat is open and water is flowing over the sensor. Could you switch the OE sender and aftermarket sensor location and see how...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 03-06-2015, 04:23 AM
Replies: 6
Views: 242
Posted By EPNCSU2006
How did you mount the sensors? It sounds like...

How did you mount the sensors? It sounds like there might be an air pocket around the sensors.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-23-2015, 04:36 AM
Replies: 3
Views: 208
Posted By EPNCSU2006
That might be for the canister purge valve,...

That might be for the canister purge valve, although I think it is supposed to be between a couple of the intake runners.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-22-2015, 06:52 AM
Replies: 11
Views: 359
Posted By EPNCSU2006
Not enough wires for EGR position. Canister purge...

Not enough wires for EGR position. Canister purge valve maybe?
Forum: Clutch, Transmission, Differential, Axle & Transfer Case 01-12-2015, 04:55 PM
Replies: 2
Views: 191
Posted By EPNCSU2006
I believe it should be an S5-47M. The -42's were...

I believe it should be an S5-47M. The -42's were never fitted with the modular bell housing.

Service manual:...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-09-2015, 04:14 AM
Replies: 8
Views: 264
Posted By EPNCSU2006
The crossmember from the newer truck will fit in...

The crossmember from the newer truck will fit in your '89. Just be sure to get the support brackets also. I think that maybe all the 5-speed crossmembers are the same F150-F350 as I used one from a...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 01-04-2015, 06:42 AM
Replies: 31
Views: 1,377
Posted By EPNCSU2006
Not to beat a dead horse, but the water pump is...

Not to beat a dead horse, but the water pump is not a high pressure pump - I think you would be lucky to see 5 psi completely dead headed. Plus, think of it this way - if a closed thermostat caused...
Showing results 1 to 15 of 500

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 03:17 AM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup