Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 500
Search took 0.77 seconds.
Search: Posts Made By: Phy
Forum: 1987 - 1996 F150 & Larger F-Series Trucks Today, 05:32 PM
Replies: 11
Views: 316
Posted By Phy
I took a caliper to mine ('93), and they're...

I took a caliper to mine ('93), and they're .680".
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 02-26-2015, 09:09 PM
Replies: 26
Views: 379
Posted By Phy
I wonder if when they installed the IP if they...

I wonder if when they installed the IP if they got the gear off a tooth or two. It sure sounds like it needs more advance...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-26-2015, 04:34 PM
Replies: 3
Views: 136
Posted By Phy
6.9 & 7.3. Thats it.

6.9 & 7.3. Thats it.
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 02-25-2015, 04:31 PM
Replies: 9
Views: 187
Posted By Phy
Have you tried jumping the starter relay? Jump...

Have you tried jumping the starter relay? Jump from the large terminal that's connected to the +battery to the small terminal (make sure it's in neutral). If it cranks, then check that the wire to...
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 02-24-2015, 07:02 PM
Replies: 4
Views: 149
Posted By Phy
Those are called "olives" here. If you change...

Those are called "olives" here. If you change the subject line of your first post to something like "Where can I get new olives for my fuel line?" I'm sure someone will chime in...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-24-2015, 03:02 PM
Replies: 37
Views: 692
Posted By Phy
In theory, yes. Manufacturing tolerances can...

In theory, yes. Manufacturing tolerances can throw a wrench into it, though...
I'd want to check the pattern & backlash before the swap and again after.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-24-2015, 11:29 AM
Replies: 2
Views: 174
Posted By Phy
I don't believe there is any difference in the...

I don't believe there is any difference in the T-cases. I'm pretty sure you can use either shifter/linkage setup. I haven't done it myself, but I've read that they're interchangeable several...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-24-2015, 12:06 AM
Replies: 6
Views: 155
Posted By Phy
Gear619, if you are talking about the input shaft...

Gear619, if you are talking about the input shaft of the 4407 being the same as the 1356 and working with your trans, I believe they are the same. The driveshafts are different.
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 02-23-2015, 11:51 PM
Replies: 28
Views: 717
Posted By Phy
Thanks. I try to make myself useful...

Thanks. I try to make myself useful...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-23-2015, 12:33 PM
Replies: 8
Views: 227
Posted By Phy
Pull the front drive shaft & test again. If it...

Pull the front drive shaft & test again. If it only vibrates with the T-case in 4wd, it's in the T-case. If it only vibrates with the hubs locked, it's in the axle. If it doesn't vibrate either...
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 02-23-2015, 12:23 PM
Replies: 28
Views: 717
Posted By Phy
Convert to right hand drive...

Convert to right hand drive...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-22-2015, 09:49 PM
Replies: 14
Views: 354
Posted By Phy
'95 and up have the best E4OD.

'95 and up have the best E4OD.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-22-2015, 02:02 PM
Replies: 19
Views: 2,830
Posted By Phy
Hey Nothing Special, when it acts up have you...

Hey Nothing Special, when it acts up have you tried turning the key over? I've had a lock cylinder that was sensitive to which side of the key. Even though both sides looked the same, there...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-21-2015, 10:10 PM
Replies: 5
Views: 203
Posted By Phy
I've read that it will, but I don't know first...

I've read that it will, but I don't know first hand...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-20-2015, 09:12 PM
Replies: 3
Views: 212
Posted By Phy
You have to cut a hole. On some cabs (I don't...

You have to cut a hole. On some cabs (I don't think all...) if you pull up the carpet you can see the stamped outline where you need to cut.
Showing results 1 to 15 of 500

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 06:19 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup