Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 497
Search took 0.21 seconds.
Search: Posts Made By: 86fordtruck
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-30-2015, 08:24 AM
Replies: 19
Views: 316
Posted By 86fordtruck
Before you get to carried away, double check that...

Before you get to carried away, double check that your firewall isn't cracked and/or flexing behind the clutch master cylinder. I replaced my clutch, which was worn and not releasing completely, but...
Forum: Garage & Workshop 01-28-2015, 09:15 PM
Replies: 10
Views: 142
Posted By 86fordtruck
I was planning on central heat and air, although...

I was planning on central heat and air, although I haven't decided on gas heat or not. It would have to be LP, as piped in natural gas is not available in this area. The engine exhaust evacuation...
Forum: Garage & Workshop 01-28-2015, 08:52 AM
Replies: 10
Views: 142
Posted By 86fordtruck
Funnel hooked to a plastic tube that exits...

Funnel hooked to a plastic tube that exits outside. I remember something similar that was in the back of old C-130's back in the 70's.
Forum: Garage & Workshop 01-27-2015, 06:54 PM
Replies: 10
Views: 142
Posted By 86fordtruck
It will have water, and I'm looking for a...

It will have water, and I'm looking for a restaraunt style stainless steel sink with side boards that can hold parts that need to be washed and have already been washed. I figured I'd locate the...
Forum: Garage & Workshop 01-26-2015, 09:42 AM
Replies: 10
Views: 142
Posted By 86fordtruck
Thanks for the link, Chris. Neat ideas, there. ...

Thanks for the link, Chris. Neat ideas, there. And thanks to Lariat, as well. I think I'm going to build a storage room for engine hoist, engine stands, etc, and I think I'll have put the air...
Forum: Garage & Workshop 01-21-2015, 09:36 PM
Replies: 10
Views: 142
Posted By 86fordtruck
Car Barn interior layout ideas

Well, I've contracted to have a 40' x 50' car barn built. It will be a pole barn, with 12' walls, and a scissors truss so I can fit a lift inside. Concrete floor, of course. The shell should be done...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-11-2015, 07:55 PM
Replies: 223
Views: 27,705
Posted By 86fordtruck
Didn't get much done this weekend. It was cold,...

Didn't get much done this weekend. It was cold, so I worked on plans for the new 40' x 50' car barn instead. Sunday afternoon, I did cut the stainless hinges out, and got them taped together and...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-09-2015, 08:52 PM
Replies: 223
Views: 27,705
Posted By 86fordtruck
This week I got in the new taillight assemblies,...

This week I got in the new taillight assemblies, as well as the magnets and solenoid to get the taillight hinge assembled. The hinges I was using were nickel plated steel, but I decided to order a...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-03-2015, 08:10 AM
Replies: 71
Views: 1,551
Posted By 86fordtruck
I second the recommendation to go with the...

I second the recommendation to go with the 351W/5.8L. I have one in my 94 F150 with the E40D trans and 3.55 rear end. Pulling an empty 1800 lb car hauler behind it, you hardly notice that it's...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-02-2015, 10:56 PM
Replies: 8
Views: 344
Posted By 86fordtruck
Manual trans makes me worry about firewall...

Manual trans makes me worry about firewall cracks. I was having some clutch issues, but also discovered leaks under cowl on the driver side. At first, I didn't think I had a firewall crack, but...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-02-2015, 07:14 PM
Replies: 223
Views: 27,705
Posted By 86fordtruck
Got the solenoid and rare earth magnets ordered,...

Got the solenoid and rare earth magnets ordered, along with the new taillight assemblies. I ordered the Dakota Digital PDR-1 actuator to push the taillight assembly open and away from the magnets...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-01-2015, 05:36 PM
Replies: 223
Views: 27,705
Posted By 86fordtruck
I looked at those, but was worried that for push...

I looked at those, but was worried that for push toggle to work, it would have to stick out to far. I want the taillight to be tight to the body and be totally undetectable. I was going to start...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-01-2015, 01:45 PM
Replies: 223
Views: 27,705
Posted By 86fordtruck
Thanks, Ken! :)

Thanks, Ken! :)
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-01-2015, 01:43 PM
Replies: 223
Views: 27,705
Posted By 86fordtruck
I went down and took a look at the taillight...

I went down and took a look at the taillight again. I could have extended the hinge another 1/2" or so, but then the mounting surface has a couple bumps in it. Below, I could mount a hinge about 1...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 01-01-2015, 01:28 PM
Replies: 223
Views: 27,705
Posted By 86fordtruck
Thanks 86 F150. That helps alot. As I continue...

Thanks 86 F150. That helps alot. As I continue to work on the fuel filler, I'll post up more pictures of that, too. :)
Showing results 1 to 15 of 497

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 03:21 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup