Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 500
Search took 0.34 seconds.
Search: Posts Made By: Torky2
Forum: Clutch, Transmission, Differential, Axle & Transfer Case Today, 12:29 AM
Replies: 2
Views: 137
Posted By Torky2
Well, since you've had no takers so far... I was...

Well, since you've had no takers so far... I was wondering what kind of surface you are driving on when this clunking happens in 4WD.

And yes, I have a Dana 44 TTB.
Forum: Big Block V8 - 385 Series (6.1/370, 7.0/429, 7.5/460) Yesterday, 11:57 PM
Replies: 1
Views: 85
Posted By Torky2
Well, your description is confusing to me, at...

Well, your description is confusing to me, at least...

The FRONT of the engine is to the right in the pic, so the rear of the block is to the LEFT. So the only sensor I see on the top REAR of the...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 01-18-2015, 12:39 AM
Replies: 13
Views: 286
Posted By Torky2
Some comments, take them for what they're...

Some comments, take them for what they're worth...

Stop calling the Upper Radiator Hose a "radiator return hose", it's the upper radiator hose, don't confuse people :)

I haven't seen a spring...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 01-07-2015, 12:46 AM
Replies: 11
Views: 338
Posted By Torky2
Is this on the Passenger (right) side of the...

Is this on the Passenger (right) side of the block? I'm wondering if it is, because of the casting number and block part number.

Often the block drain on the passenger side of V8's is blocked by...
Forum: Cooling, Heating, Ventilation & A/C 01-02-2015, 12:33 AM
Replies: 7
Views: 204
Posted By Torky2
Well, I can tell you what I have, and I am happy...

Well, I can tell you what I have, and I am happy with them:

Vacuum Pump - Robinair 15234, a 1.2 cu./ft. two-stage pump with gas ballast. I don't think they are made anymore, but it was in...
Forum: 1978 - 1996 Big Bronco 12-27-2014, 01:36 AM
Replies: 23
Views: 643
Posted By Torky2
Then it's OBD-I, and that MAP sensor should be...

Then it's OBD-I, and that MAP sensor should be hooked up solidly to manifold vacuum :)
Forum: 1978 - 1996 Big Bronco 12-27-2014, 01:33 AM
Replies: 14
Views: 388
Posted By Torky2
A few minutes under the Bronc with a tape measure...

A few minutes under the Bronc with a tape measure will tell you.
Measure vertical trans height from bottom of the pan to the top of the bellhousing.
To that number, add the vertical height off of...
Forum: 1978 - 1996 Big Bronco 12-27-2014, 01:20 AM
Replies: 5
Views: 266
Posted By Torky2
Typical intake manifold/throttle body crud = PCV...

Typical intake manifold/throttle body crud = PCV system fume pickup from crankcase, intake flow reversion, EGR gasses. I think the first one is far away the biggest source.

The late 80's/early...
Forum: 1978 - 1996 Big Bronco 12-27-2014, 01:08 AM
Replies: 23
Views: 643
Posted By Torky2
I'm a bit confused... is there any driving mode...

I'm a bit confused... is there any driving mode that it DOESN'T buck?


No. The MAP sensor has a hose to it from manifold vacuum... if yours doesn't, you found a problem!


49-State 5.8L's were...
Forum: Cooling, Heating, Ventilation & A/C 12-17-2014, 12:54 AM
Replies: 6
Views: 269
Posted By Torky2
Rockauto is nice, as you can have multiple years...

Rockauto is nice, as you can have multiple years open at once in their catalog, and flip between parts to compare. Or open two instances of browser and flip instances to compare years.
First I think...
Forum: Cooling, Heating, Ventilation & A/C 12-15-2014, 01:15 AM
Replies: 6
Views: 269
Posted By Torky2
About two years ago I totally replaced the A/C on...

About two years ago I totally replaced the A/C on my Bronco. 1994 was the first year for R-134a. The compressor had seized, and with that, and the age of all the hoses etc., I replaced everything...
Forum: 1997 - 2003 F150 12-03-2014, 01:11 AM
Replies: 6
Views: 255
Posted By Torky2
Yeow! Well, just some quick thoughts, other...

Yeow!

Well, just some quick thoughts, other than "ya just shouldn't have done it..."

The new bolts ARE the proper bolts, right?

It would seem that if the holes in the crankshaft are stripped...
Forum: 1997 - 2003 F150 12-03-2014, 12:51 AM
Replies: 17
Views: 539
Posted By Torky2
Yeah, let us know what you find. Pulling...

Yeah, let us know what you find.

Pulling dashes back is best viewed from a distance........ like over the internet :D

Ya sure it wouldn't be easier to just change friends? :)
Forum: 1978 - 1996 Big Bronco 12-03-2014, 12:44 AM
Replies: 2
Views: 185
Posted By Torky2
If the truck has the Super/Max Cooling option,...

If the truck has the Super/Max Cooling option, there is another possible oil to antifreeze leak path -- an engine oil cooler leak. If it has it, the oil filter mounts onto the oil cooler, the oil...
Forum: 1978 - 1996 Big Bronco 12-03-2014, 12:24 AM
Replies: 5
Views: 200
Posted By Torky2
Well, I would replace the fuel filter first, cuz...

Well, I would replace the fuel filter first, cuz their cheap and easy, and then you'll know it's clean. If that has no effect, I'd grab a length of rubber fuel line, like 6-10 feet long, and connect...
Showing results 1 to 15 of 500

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 02:28 AM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup