Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 36
Search took 0.05 seconds.
Search: Posts Made By: gas6999
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-23-2015, 02:58 PM
Replies: 73
Views: 3,658
Posted By gas6999
glad you found one. George.

glad you found one. George.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-23-2015, 06:02 AM
Replies: 73
Views: 3,658
Posted By gas6999
cam pin

how long do you need? I have a few around, the best place to get them is from a cam company, let me know how long you need and ill look to see if I have one. George.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-18-2015, 07:42 AM
Replies: 73
Views: 3,658
Posted By gas6999
cam

that cam has seen better days, I would not run it, check craigslist, for a good used one, I have found some real good cams on there, but do your self a favor and get a new set of lifters, 90.00 on...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-17-2015, 07:16 AM
Replies: 73
Views: 3,658
Posted By gas6999
cam

you need to make sure its still straight, I would put it in the block and spin it to make sure you didn't bend it when you dropped it, or if you have vblocks and a dial indicator, you can turn it and...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-13-2015, 05:56 PM
Replies: 73
Views: 3,658
Posted By gas6999
cam and convertor

if you are running a better cam that will come in around 1500- 1800, you will want to loosen up the convertor. a stock convertor locks up around 900-1000 rpm that wont let the engine get up to where...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-12-2015, 04:24 PM
Replies: 73
Views: 3,658
Posted By gas6999
cam

im running almost the same setup in my engine I built for my 54, im running a b303 cam from ford, its like one step up from from a stock mustang roller, it has .480 lift and 284 duration, im also...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-11-2015, 09:10 AM
Replies: 73
Views: 3,658
Posted By gas6999
engine

your project looks like its going well, did you have the block board, or honed at the machine shop? make sure you put the cross hatch pattern back in the boars so the rings can seat,, you will need...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-10-2015, 09:01 AM
Replies: 7
Views: 408
Posted By gas6999
engine

a good 302 and a aod, trans , are a good swap for theses trucks, aod trans are cable operated so no electronics required, 302 are every where, cheap ,make good power and are well supported buy the...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-04-2015, 10:26 AM
Replies: 5
Views: 284
Posted By gas6999
dash

Its all how bad you want to change it, it can be done but its not a bolt in dash, I put a 51 Victoria dash in my 54 looks great, but my dash was cut to pieces so I had to do something with it, I...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 12-29-2014, 09:52 AM
Replies: 3
Views: 191
Posted By gas6999
carb

also I would run a vacuum secondary carb if you go with a holley for the street.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 12-29-2014, 09:51 AM
Replies: 3
Views: 191
Posted By gas6999
carb

a 650 is plenty for the street, unless you have a killer cam and heads you wont need anymore than 650cfm, I run holley,s in all my cars, and if they set along time the float will stick, but if you...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 12-24-2014, 09:48 AM
Replies: 69
Views: 3,277
Posted By gas6999
explorer chassis

have you thought about using a explorer chassis under your f100?
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-08-2014, 12:18 PM
Replies: 20
Views: 874
Posted By gas6999
hey crs,im in Lakeland fl and am right in the...

hey crs,im in Lakeland fl and am right in the middle of a frame swap with a explorer, with that being said, if you don't have a welder and some fab skills, I think you should get another original...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-30-2014, 06:33 PM
Replies: 10
Views: 928
Posted By gas6999
man it looks great, dadsgp, im also putting a 54...

man it looks great, dadsgp, im also putting a 54 on a explorer frame, so far its turning out great I used the explorer floor and firewall, but hind sight I would have done it the way you are, keep...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-27-2014, 09:03 AM
Replies: 30
Views: 8,928
Posted By gas6999
jada0327, checkout the explorer frame they are...

jada0327, checkout the explorer frame they are 1" longer than stock, most people use then already have the rack and pinion and 8.8 rear! its the only way to go!! George.
Showing results 1 to 15 of 36

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 11:56 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup