Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 239
Search took 0.05 seconds.
Search: Posts Made By: 49fordv8f4
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-23-2015, 10:50 PM
Replies: 7
Views: 297
Posted By 49fordv8f4
The mirror bracket is actually fairly easy to...

The mirror bracket is actually fairly easy to make, take a look at Bob's site. I made one for my F4. The passenger side bracket is very hard to find, used. Dennis Carpenter is reproducing both side...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-21-2015, 10:19 PM
Replies: 496
Views: 88,800
Posted By 49fordv8f4
This is looking very good! You did a beautiful...

This is looking very good! You did a beautiful job on the cab mods.
Mark
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-21-2015, 05:54 PM
Replies: 10
Views: 229
Posted By 49fordv8f4
With the diaphragm on the axle and with no vacuum...

With the diaphragm on the axle and with no vacuum to it, it locks the axle in low. The diaphragm pulls the shift arm on the axle to high when vacuum is applied.
Mark
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-21-2015, 01:08 PM
Replies: 10
Views: 229
Posted By 49fordv8f4
You should be able to take the diaphragm off of...

You should be able to take the diaphragm off of the axle and make a piece to replace it that will lock it in high range. Do not try to rely on the vacuum to hold it in high, It must be mechanically...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-19-2015, 06:32 PM
Replies: 16
Views: 256
Posted By 49fordv8f4
My pto is a Chelsea. Mark

My pto is a Chelsea.
Mark
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-18-2015, 11:35 PM
Replies: 16
Views: 256
Posted By 49fordv8f4
No problem, the transmission is still on the...

No problem, the transmission is still on the workbench. Besides, I'm curious now.
Mark
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-18-2015, 05:46 PM
Replies: 16
Views: 256
Posted By 49fordv8f4
Tom, Ok I will take them for you when I get a...

Tom, Ok I will take them for you when I get a chance in the next week or so.
Mark
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-18-2015, 05:43 PM
Replies: 16
Views: 256
Posted By 49fordv8f4
Not sure, I will have to look. Mark

Not sure, I will have to look.
Mark
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-18-2015, 05:06 PM
Replies: 16
Views: 256
Posted By 49fordv8f4
Pinecone, I have a PTO on my '49 F4. I have all...

Pinecone, I have a PTO on my '49 F4. I have all the levers off right now, I could send you some photos if you are interested. They would be simple to duplicate.
Ross, the shaft should be reversible...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-18-2015, 05:02 PM
Replies: 16
Views: 256
Posted By 49fordv8f4
I just scrapped out a couple. I saved the same...

I just scrapped out a couple. I saved the same parts you mentioned. Both of mine had good rear mounts. I don't need any of the parts, but I didn't want to see them go for scrap. Both transmissions...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-17-2015, 06:43 PM
Replies: 64
Views: 2,399
Posted By 49fordv8f4
Looking Good ! :-X22 Mark

Looking Good ! :-X22
Mark
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-16-2015, 10:17 PM
Replies: 26
Views: 733
Posted By 49fordv8f4
If he found a 223 out of a car, would all of the...

If he found a 223 out of a car, would all of the trim and pan off of his 215 fit?
Mark
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 01-16-2015, 10:12 PM
Replies: 19
Views: 568
Posted By 49fordv8f4
'42-'47 jailbars Mark

'42-'47 jailbars
Mark
Forum: 1947 and Older Ford Trucks 01-16-2015, 08:56 PM
Replies: 24
Views: 415
Posted By 49fordv8f4
That sounds like a plan to me. I believe you have...

That sounds like a plan to me. I believe you have it under control:-X22
Mark
Forum: 1947 and Older Ford Trucks 01-16-2015, 08:32 PM
Replies: 24
Views: 415
Posted By 49fordv8f4
I usually try to find a socket or a piece of...

I usually try to find a socket or a piece of round stock that is close to the size of the OD and drive or press it in by the outside edge. You may deform it with a socket or tube driving from the...
Showing results 1 to 15 of 239

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »


All times are GMT -5. The time now is 03:43 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup