Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 500
Search took 0.48 seconds.
Search: Posts Made By: ken75ranger
Forum: EcoBoost (all engine sizes) 01-03-2012, 06:03 PM
Replies: 121
Views: 75,904
Posted By ken75ranger
Personallly I would call the dealer back and ask...

Personallly I would call the dealer back and ask if they found any missfires in mode 6. It should store the missfires there even if the CEL isn't staying on.
I did see this on another forum.

"So...
Forum: 2009 - 2014 F150 01-03-2012, 05:41 PM
Replies: 36
Views: 7,819
Posted By ken75ranger
I have an 11 scab. No leaks after a tornado and...

I have an 11 scab. No leaks after a tornado and Hurricane Irene.
Well there was the one time I forgot to close the slider.... :-roll
Forum: 2009 - 2014 F150 01-03-2012, 05:18 PM
Replies: 86
Views: 7,589
Posted By ken75ranger
Maybe I missed it but didn't the OP put in bigger...

Maybe I missed it but didn't the OP put in bigger tires and a lift?
Did it get re-programmed for those tires?
That could easily explain the low mpg.
Forum: 2009 - 2014 F150 10-30-2011, 07:45 AM
Replies: 22
Views: 1,718
Posted By ken75ranger
Text to Sync works fine with my Droid2. I've...

Text to Sync works fine with my Droid2.
I've heard with the latest software update to the iphones it will work for them also.
Forum: Super Duty & Heavy Duty 11-26-2009, 03:38 PM
Replies: 27
Views: 2,223
Posted By ken75ranger
Why is it a gonner? Side gears and spiders will...

Why is it a gonner? Side gears and spiders will have a degree or 2 of play.
Post up a pic of the bad shaft so we can take a look.
Forum: Super Duty & Heavy Duty 11-24-2009, 06:51 PM
Replies: 27
Views: 2,223
Posted By ken75ranger
Either way you're going to have to pull the...

Either way you're going to have to pull the shaft. It shouldn't rest on the balljoint.
Forum: Super Duty & Heavy Duty 11-23-2009, 08:57 PM
Replies: 2
Views: 699
Posted By ken75ranger
You're probably going to run into a driveshaft...

You're probably going to run into a driveshaft geometry issue. Your pinion yoke angle should match you're output yoke angle within 2 degrees. The pinion angle can be slightly lower. You'll probably...
Forum: Super Duty & Heavy Duty 11-23-2009, 08:39 PM
Replies: 27
Views: 2,223
Posted By ken75ranger
Pull the axleshaft. It's probably broken.

Pull the axleshaft. It's probably broken.
Forum: New York Chapter 07-24-2009, 03:52 PM
Replies: 2
Views: 268
Posted By ken75ranger
There's an OHV event coming up in August....

There's an OHV event coming up in August. http://www.trailrex.com/
Last year was great and should be bigger and better this year.
Forum: New York Chapter 06-14-2009, 07:28 AM
Replies: 2
Views: 222
Posted By ken75ranger
I've been busy

I spent this winter doing some suspension mods to my '75 Bronco.
5 link front and rear. Front uses stock style EB coils and shocks. The rear is 10 inch coilovers. Moved up in tires size to 35 inch...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 12-02-2008, 09:23 AM
Replies: 12
Views: 855
Posted By ken75ranger
I'd try a 5.0 mustang rubber boot for the...

I'd try a 5.0 mustang rubber boot for the distributor first. don't forget to use some dielectric grease on all the connections. .If you still have issues a remote TFI might help. Most guys I know...
Forum: Performance & General Engine Building 10-09-2008, 01:00 PM
Replies: 7
Views: 316
Posted By ken75ranger
I wouldn't use a HV pump if you don't need it. I...

I wouldn't use a HV pump if you don't need it. I know a few guys that have had cams-distributor gears get wiped out from turning the HV pump.
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 10-09-2008, 12:43 PM
Replies: 28
Views: 498
Posted By ken75ranger
You could still do a modern roller block if you...

You could still do a modern roller block if you want to. Wildhorses sell a kit that takes the place of the old boss on the block.
EFI Clutch Equalizer Conversion Bracket - WILD HORSES Early Ford...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 08-13-2008, 06:59 AM
Replies: 16
Views: 458
Posted By ken75ranger
It's possible but not likely. What crank is it?...

It's possible but not likely. What crank is it? What balancer did you use?
Forum: New York Chapter 08-07-2008, 08:58 PM
Replies: 22
Views: 698
Posted By ken75ranger
Tim's truck is all done. I did forget the camera...

Tim's truck is all done. I did forget the camera but the guys at Rock Krawler sent me some pics.
http://classicbroncos.com/photos/showphoto.php/photo/16728/size/big/cat/500
4 inch lift. The front...
Showing results 1 to 15 of 500

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »





All times are GMT -5. The time now is 05:16 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup