Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 68
Search took 0.02 seconds.
Search: Posts Made By: Tigauto
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 10-05-2014, 12:44 AM
Replies: 41
Views: 1,125
Posted By Tigauto
Very nice job

Very nice job
Forum: 6.0L Power Stroke Diesel 10-04-2014, 10:12 PM
Replies: 21
Views: 634
Posted By Tigauto
Snap on and Matco have sockets for that. If the...

Snap on and Matco have sockets for that. If the bolt or nut is rounded the socket has sharp edges to bit into the bolt. As a tech these sockets are worth every dime. You may need to heat the bolts up...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 10-04-2014, 10:01 PM
Replies: 41
Views: 1,125
Posted By Tigauto
The flange tool is worth every dime I payed for...

The flange tool is worth every dime I payed for it. The one I purchased flanges and you turn the tool around and it punches holes. So on your repair panel you flange it, then punch the holes were the...
Forum: 2004 - 2008 F150 09-08-2014, 09:33 PM
Replies: 0
Views: 283
Posted By Tigauto
2007 5.4 to 4.6 two wheel drive

Looking for information thinking of swapping 5.4 to 4.6 on 2007 2 wheel drive.
I know the trans and ECM, harness will need to be changed but wondering if front pipe will fit. The reason is the truck...
Forum: 2004 - 2008 F150 09-08-2014, 09:24 PM
Replies: 12
Views: 965
Posted By Tigauto
I would check to see if the injector oil rings...

I would check to see if the injector oil rings are leaking or an injector.
Forum: 2004 - 2008 F150 09-08-2014, 09:17 PM
Replies: 2
Views: 330
Posted By Tigauto
Check the ball joints could be seizing

Check the ball joints could be seizing
Forum: 2004 - 2008 F150 09-04-2014, 03:55 PM
Replies: 35
Views: 2,595
Posted By Tigauto
What was the work preformed on the truck? Cam...

What was the work preformed on the truck? Cam phasers and chain I guess.
Ford should have warned you about the other problems that could come up.
Like I posted before the 5.4 is known for taking...
Forum: 2009 - 2014 F150 08-20-2014, 10:44 PM
Replies: 4
Views: 647
Posted By Tigauto
Fuel caps have not vented for years, we need more...

Fuel caps have not vented for years, we need more information to help you.
You said the starter will engage but does it crank? Is you security light flashing?
Will it crank but not start? If this...
Forum: 2004 - 2008 F150 08-20-2014, 08:33 PM
Replies: 46
Views: 3,008
Posted By Tigauto
Looks like the head is done! That engine has been...

Looks like the head is done! That engine has been running real rich, even looks like it's been burning oil. Are you going for rebuild or used? Just watch your core charge they may charge back because...
Forum: 2004 - 2008 F150 08-20-2014, 05:13 PM
Replies: 2
Views: 458
Posted By Tigauto
Thank for the information But am putting a 2008...

Thank for the information
But am putting a 2008 in a 2007 the information I am looking for can you switch
Vin 5 to vin V
Forum: 2004 - 2008 F150 08-19-2014, 09:40 AM
Replies: 2
Views: 458
Posted By Tigauto
Need information 2007 vin 5 to 2008 vin V

I am looking to swap 2007 vin 5 to 2008 vin V 5.4. Just wondering what would need to be changer? Would the ECM need to be replaced? I believe the vin V is flex fuel. Any help would be great
Forum: 2004 - 2008 F150 08-13-2014, 02:54 PM
Replies: 46
Views: 3,008
Posted By Tigauto
Remove the head and see what the top of the...

Remove the head and see what the top of the piston looks like. The piston more the likely will be smashed. See if there is damage to the cly walls, your best bet is to remove the engine. It's not bad...
Forum: 2004 - 2008 F150 08-12-2014, 10:20 PM
Replies: 46
Views: 3,008
Posted By Tigauto
Good luck finding cylinder heads! That's the...

Good luck finding cylinder heads! That's the problem with the 5.4 no bearings for cams. The intake, harness will come with the engine and ask for the breather when you find the engine.
The ECM will...
Forum: 2004 - 2008 F150 08-12-2014, 04:37 PM
Replies: 46
Views: 3,008
Posted By Tigauto
The 4.6 for your truck should fit right in with...

The 4.6 for your truck should fit right in with the ECM out of the same truck. I believe from 2006 and older are just a bolt up, the coils will need to be changed.
Just make sure starter is in the...
Forum: EcoBoost (all engine sizes) 08-10-2014, 07:59 PM
Replies: 39
Views: 25,938
Posted By Tigauto
Well if you are getting black soot on the tail...

Well if you are getting black soot on the tail pipes that tells you what's going on in the combustion chamber. I don't have the TSB with me but there is information from a ford tech on you tube. This...
Showing results 1 to 15 of 68

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »





All times are GMT -5. The time now is 03:11 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup