Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 499
Search took 0.45 seconds.
Search: Posts Made By: Kemicalburns
Forum: 1978 - 1996 Big Bronco 12-19-2014, 11:02 AM
Replies: 1
Views: 110
Posted By Kemicalburns
yes and no. the transmission will bolt up. using...

yes and no. the transmission will bolt up. using the correct flexplate is a must and wouldn't be transferable from 302 to a 351w.

What trans are we talking about from the 88 and what is in the 86...
Forum: 1978 - 1996 Big Bronco 12-17-2014, 10:22 AM
Replies: 1
Views: 184
Posted By Kemicalburns
any seat set from an F250/F350 giving you 3 seats...

any seat set from an F250/F350 giving you 3 seats across is a bolt in affair. I went a step further and simply bolted in the center jump seat alone and went with 90 Mustang GT seats in the...
Forum: 1978 - 1996 Big Bronco 12-16-2014, 11:00 AM
Replies: 2
Views: 135
Posted By Kemicalburns
You must be at a complete stop and put Tcase in...

You must be at a complete stop and put Tcase in neutral to go into 4L. is 4H working at all? have you checked the fluid level in the Tcase? also just because the linkage looks good doesn't mean its...
Forum: 1978 - 1996 Big Bronco 12-12-2014, 12:32 PM
Replies: 7
Views: 229
Posted By Kemicalburns
A stock C6 no, a built C6 with the proper TC and...

A stock C6 no, a built C6 with the proper TC and so forth may be ok. Heck a built AOD would be ok as well and you would gain Overdrive.
Forum: 1978 - 1996 Big Bronco 12-10-2014, 04:24 PM
Replies: 3
Views: 195
Posted By Kemicalburns
that's not to many miles for a 302, have you gone...

that's not to many miles for a 302, have you gone thru all the typical tune up stuff to help it? Pull codes etc...

motor swap can be cheap or expensive, depends if you plan to pull motor. buy a...
Forum: 1978 - 1996 Big Bronco 12-10-2014, 02:50 PM
Replies: 7
Views: 318
Posted By Kemicalburns
the ZF has a granny low and is a 5 speed. not to...

the ZF has a granny low and is a 5 speed. not to mention bulletproof like the NP435.
Forum: 1978 - 1996 Big Bronco 12-09-2014, 07:40 PM
Replies: 10
Views: 203
Posted By Kemicalburns
same bolt pattern with either motor. the flywheel...

same bolt pattern with either motor. the flywheel is the crucial part as the imbalance from 5.0 to 5.8 are different.
Forum: 1978 - 1996 Big Bronco 12-09-2014, 07:37 PM
Replies: 7
Views: 318
Posted By Kemicalburns
so me telling you to find a ZF instead wont fly?...

so me telling you to find a ZF instead wont fly? ive seen that m5 trans break behind he 300-6 way to often.

yes you can probably use your tcase, if its an Etcase currently on that 5 speed its...
Forum: 1978 - 1996 Big Bronco 12-07-2014, 11:36 AM
Replies: 3
Views: 252
Posted By Kemicalburns
Rear mains seal work can get spendy depending on...

Rear mains seal work can get spendy depending on the shop. either the motor is pulled or the transmission/tcase. its labor intensive, the part is around $10. If you can turn a wrench most of this can...
Forum: 1978 - 1996 Big Bronco 12-07-2014, 11:36 AM
Replies: 3
Views: 252
Posted By Kemicalburns
Rear mains seal work can get spendy depending on...

Rear mains seal work can get spendy depending on the shop. either the motor is pulled or the transmission/tcase. its labor intensive, the part is around $10. If you can turn a wrench most of this can...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 12-02-2014, 04:51 PM
Replies: 14
Views: 3,143
Posted By Kemicalburns
what you will have fun with is the exhaust...

what you will have fun with is the exhaust manifolds. finding shorty headers that will fit correctly due to the spark plug angle is a nightmare and expensive.
Forum: 1978 - 1996 Big Bronco 12-01-2014, 10:55 AM
Replies: 8
Views: 224
Posted By Kemicalburns
is there ATF in the pump? positive the serp belt...

is there ATF in the pump? positive the serp belt is routed correctly?
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 11-23-2014, 11:32 PM
Replies: 19
Views: 841
Posted By Kemicalburns
well a 93 will be a flat tappet cam, 94+ had...

well a 93 will be a flat tappet cam, 94+ had roller cams
Forum: 1978 - 1996 Big Bronco 11-22-2014, 11:24 AM
Replies: 12
Views: 341
Posted By Kemicalburns
you should be airing down when playing in the...

you should be airing down when playing in the sand so a 12.5 wide tire is sufficient. moving the axle forward helps keep the tire away from the rear corner of the front fender. this occurs anytime...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 11-21-2014, 02:17 PM
Replies: 19
Views: 841
Posted By Kemicalburns
what year motor and rig is this for? ...

what year motor and rig is this for?

conanski has you on the right track to get a different cam. going with a car style intake on a truck will also require some creative fab to get the throttle...
Showing results 1 to 15 of 499

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »





All times are GMT -5. The time now is 12:15 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup