Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 500
Search took 0.36 seconds.
Search: Posts Made By: orich
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks Today, 12:07 AM
Replies: 6
Views: 209
Posted By orich
Maybe check the HEI that it has the 1/4 hex shaft...

Maybe check the HEI that it has the 1/4 hex shaft and not damaged or stripped. And may be since it made off short all kinds of things can get shipped to the US.
orich
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks Yesterday, 11:36 PM
Replies: 10
Views: 219
Posted By orich
.. 2x on the starting by pass circuit. But...

..
2x on the starting by pass circuit. But guess most guys have no idea where or how to check this.

Ford had issues yrs ago with the ign. switch that the round rear plug contacts. These were...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks Yesterday, 11:12 PM
Replies: 4
Views: 128
Posted By orich
Being it's a newer rebuilt pump most likely be...

Being it's a newer rebuilt pump most likely be okay.
Orich
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks Yesterday, 11:04 PM
Replies: 16
Views: 237
Posted By orich
Yal missed this none of ya noticed the 67 ask...

Yal missed this none of ya noticed the 67 ask tray .The plastic pull out lever is mounted about a 1/2" lower then 68-72's ..
Orich
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-20-2014, 10:47 PM
Replies: 8
Views: 175
Posted By orich
check points gap .017 & 0.34 on plugs. Check the...

check points gap .017 & 0.34 on plugs. Check the ground wire in dizzy that not broken.

Check for dizzy shaft for to much back & fourth side to side play & points are opening when you crank the...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-20-2014, 11:18 AM
Replies: 8
Views: 175
Posted By orich
Best to find TDC with placing your thumb over the...

Best to find TDC with placing your thumb over the plug hole while cranking or bumping the engine. use a remote push button switch on the solenoid. Or a screw driver can be used jumping the large...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-18-2014, 01:07 AM
Replies: 53
Views: 1,117
Posted By orich
This is why, I call him the come back kid. If...

This is why, I call him the come back kid.
If his truck goes down he's right back up in no time leaving a trail of dust
racing down the desert roads.
Orich
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-17-2014, 09:48 PM
Replies: 3
Views: 186
Posted By orich
I bought 1.1/2" trim side moulding 2 months ago...

I bought 1.1/2" trim side moulding 2 months ago looks okay but have not in stalled it yet.

I remove the old 3.3/8" stuff like you have and shxt canned it. So first got to fill all those rivet...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-16-2014, 07:00 PM
Replies: 49
Views: 2,989
Posted By orich
As long as a man is happy parting with this money...

As long as a man is happy parting with this money and seeing where it goes then it's all good.

Orich
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-16-2014, 02:28 PM
Replies: 12
Views: 446
Posted By orich
The 71 don't have any clips orich

The 71 don't have any clips
orich
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-16-2014, 02:19 PM
Replies: 62
Views: 2,640
Posted By orich
Old Pearl the girl seems to be giving you a hard...

Old Pearl the girl seems to be giving you a hard time. women!:-X19

I'd Bench test your starter jumper cables & see how it spins okay.. To bleed air remove upper intake heater hose until fluid...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-16-2014, 10:02 AM
Replies: 7
Views: 170
Posted By orich
A simple temp sensor or moisture has been known...

A simple temp sensor or moisture has been known to screw things up.
Tanny speed pickup/speedometer many little things. O2 sensor.

A bad catalytic convertor runs good until engine warm up then...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-16-2014, 09:45 AM
Replies: 53
Views: 1,117
Posted By orich
with Hyd lifters your at a pretty high rpm to...

with Hyd lifters your at a pretty high rpm to float a valve, could have been an exh or sucked it. But will find out soon ?
orich
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-15-2014, 09:27 AM
Replies: 82
Views: 3,062
Posted By orich
YEP That's it.. Like I said common problem...

YEP That's it..
Like I said common problem with newbies when rebuilding.:-roll

Orich
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 12-14-2014, 12:03 AM
Replies: 62
Views: 2,640
Posted By orich
"Dang" no fun removing broken stud if it snapped...

"Dang" no fun removing broken stud if it snapped with no threads to grab and work with.
I've worked them out with a small chisel & wd-40.

But now days there is some real good ez outs but not...
Showing results 1 to 15 of 500

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »





All times are GMT -5. The time now is 02:30 AM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup