Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Showing results 1 to 15 of 225
Search took 0.35 seconds.
Search: Posts Made By: husky390
Forum: Expedition & Navigator 11-03-2013, 08:09 PM
Replies: 7
Views: 806
Posted By husky390
I HAVE HEAT AGAIN!!!!!! I replaced the...

I HAVE HEAT AGAIN!!!!!! I replaced the thermostat, blend door, heater core and the actuator. The blend door was fine, no cracks present so I'm thinking heater core or actuator (though the...
Forum: Cooling, Heating, Ventilation & A/C 11-03-2013, 08:08 PM
Replies: 9
Views: 1,002
Posted By husky390
I HAVE HEAT AGAIN!!!!!! I replaced the...

I HAVE HEAT AGAIN!!!!!! I replaced the thermostat, blend door, heater core and the actuator. The blend door was fine, no cracks present so I'm thinking heater core or actuator (though the...
Forum: Cooling, Heating, Ventilation & A/C 11-02-2013, 06:54 PM
Replies: 9
Views: 1,002
Posted By husky390
I pulled the actuator before I yanked the dash. ...

I pulled the actuator before I yanked the dash. What I did was cut the carpet down the center which gave me enough free play to pull the floor vent supplying the rear up high enough to pull that...
Forum: Cooling, Heating, Ventilation & A/C 11-02-2013, 06:18 PM
Replies: 9
Views: 1,002
Posted By husky390
Thanks. The dash is pulled. I noticed the foam...

Thanks. The dash is pulled. I noticed the foam around the door leading to the two center dash vents was all messed up and was not sitting on its frame. Fixed that. Pulled the blend door and of...
Forum: Cooling, Heating, Ventilation & A/C 11-02-2013, 05:11 PM
Replies: 9
Views: 1,002
Posted By husky390
Thanks. I replaced the warm/closed potentiometer...

Thanks. I replaced the warm/closed potentiometer this morning and had hot air blowing for about 30 seconds and then it turned cold. It would stay cold until I turned the fan back down to low and...
Forum: Cooling, Heating, Ventilation & A/C 11-02-2013, 11:32 AM
Replies: 9
Views: 1,002
Posted By husky390
2000 Ford Expedition Blend Door Help Needed

I'm trying to remove the blend door actuator so I can continue trouble shooting. Problem is, there's a floor duct in the way. I've removed the two bolts holding it, but I cannot get it out. How...
Forum: Expedition & Navigator 11-01-2013, 10:59 PM
Replies: 7
Views: 806
Posted By husky390
2000 Ford Expedition Blend Door Project- Need Help

I'm trying to remove the blend door actuator so I can continue trouble shooting. Problem is, there's a floor duct in the way. I've removed the two bolts holding it, but I cannot get it out. How do...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 07-26-2013, 12:15 AM
Replies: 17,471
Views: 1,056,877
Posted By husky390
Scored the exhaust downtubes plus cat, EGR...

Scored the exhaust downtubes plus cat, EGR sensor, IAC sensor, new airbox and duct work, and the vacuum sensor thingy that's on the front of the manifold plus all of their plugs for $100.00. Plus I...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 07-23-2013, 08:47 PM
Replies: 0
Views: 338
Posted By husky390
1990 F250 KOEO code help

I have a 1990 F250, 5.8, 5spd, 4x4, speed density engine.
The problem I've been having is an erratic idle and it will not rev past 3k. The whole truck shakes and shimmies. It could be a bad cat...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 06-01-2013, 12:56 PM
Replies: 278
Views: 27,791
Posted By husky390
You scrapped a HI Boy!?!! :(

You scrapped a HI Boy!?!! :(
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 05-05-2013, 12:10 AM
Replies: 1
Views: 479
Posted By husky390
My 90 does the same thing. It will be really...

My 90 does the same thing. It will be really loud when it's been cold out and I haven't started it in a week. It comes from the passenger side of the engine. It usually stops once the engine warms...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-27-2013, 11:56 PM
Replies: 17,471
Views: 1,056,877
Posted By husky390
Checked the rear diff fluid to make sure it was...

Checked the rear diff fluid to make sure it was at the proper level and looked good. Also adjust the rear brakes some more. Also did some more research on a new cat for it.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-27-2013, 08:13 PM
Replies: 11
Views: 1,506
Posted By husky390
subscribing

subscribing
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-27-2013, 07:38 PM
Replies: 47
Views: 41,103
Posted By husky390
Thanks, so basically I need to start with the...

Thanks, so basically I need to start with the module and make sure that is not frozen? Also, would the reverse lights not working have anything to do with the cruise not working?
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-27-2013, 12:59 AM
Replies: 47
Views: 41,103
Posted By husky390
If the cruise module is frozen, would the cruise...

If the cruise module is frozen, would the cruise dash light still turn on? My 90 F250's horn and brake lights work. Sensor on master cylinder is zip tied on so that could be the issue.
Showing results 1 to 15 of 225

 
Forum Jump
 

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »





All times are GMT -5. The time now is 11:16 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup