Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Welcome to Ford-Trucks Forums!
Welcome to Ford-Trucks.com.

You are currently viewing our forums as a guest, which gives you limited access to view most discussions and access our other features. By joining our community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join the Ford-Trucks Forums community today!


Showing results 1 to 15 of 97
Search took 0.37 seconds.
Search: Posts Made By: lm987
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 11-13-2014, 04:29 PM
Replies: 18
Views: 598
Posted By lm987
Remote fill brake fluid reservoir

I would add photos if I could figure out how to post them. Help please!!
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 11-13-2014, 02:32 PM
Replies: 18
Views: 598
Posted By lm987
Remote Brake Fluid Reservoir

Greetings,

I have installed a remote fill reservoir on the firewall of my 1950 F-1 but filled the master cylinder before installing the remote fill. My question is that I am not sure how it is...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 10-12-2014, 08:12 PM
Replies: 24
Views: 1,259
Posted By lm987
Fiberglass Fenders

FOOMOO,

Thanks for your input. Who are "Bebops" Thanks.
Mike
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 10-12-2014, 04:37 PM
Replies: 24
Views: 1,259
Posted By lm987
Fiberglass Fenders

Thanks Ben. I must decide on a steel one with the cost of repairing it to a new set of fiberglass ones.
COWBOYS???? We shall see!
Mike
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 10-12-2014, 01:46 PM
Replies: 24
Views: 1,259
Posted By lm987
May I ask where you bought your fiberglass...

May I ask where you bought your fiberglass fenders?? and had no issues with them?? Good steel ones are very hard to find.
Thanks.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 10-11-2014, 01:35 PM
Replies: 24
Views: 1,259
Posted By lm987
Fiberglass Front Fenders

I would like to add my 2 cents to the fiberglass issue. I had two used front ones made by Fairlane Ford for my 1950 F-1 which were supposed to be one of the best. They fit fine until I got to adding...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 10-08-2014, 12:14 PM
Replies: 4
Views: 314
Posted By lm987
Lower Fender clearance

Thanks guys. This quite a bit.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 10-06-2014, 04:48 PM
Replies: 4
Views: 314
Posted By lm987
1950 F-1 Lower Fender Installation

Greetings all,

Could anyone tell me the approximate distance between the lower fenders edge and where they cross the frame to be bolted up to the lower panel??

I have one that is essentially on...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 08-12-2014, 10:46 AM
Replies: 5
Views: 693
Posted By lm987
Easy -out removal

I have the exact same problem. Does any one know of an alternate location for the oil pressure sender location???
Thanks
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 07-06-2014, 12:05 PM
Replies: 6
Views: 317
Posted By lm987
Valve train

I checked for any gap between the rocker arm and pushrod when torqued but there is none on any of them.
Perhaps I should just let it run after replacing the rocker arm nuts????
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 07-06-2014, 11:39 AM
Replies: 6
Views: 317
Posted By lm987
Valve train Issue

Thanks for your reply. I have the rail type rockers as shown on the right in your photo. They are new but the nuts that were supplied with them are apparently not doing their job and allow the rocker...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 07-05-2014, 05:12 PM
Replies: 6
Views: 317
Posted By lm987
302 Valve train

Greetings to all.
I have a 1971 Ford 302 installed in my Ford F-1. My issue is with adjusting or doing the initial setting of the valves. It has hydraulic lifters and standard length pushrods. The...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 04-15-2014, 01:27 PM
Replies: 11
Views: 508
Posted By lm987
Rear Brake Cables

I also used stock brake cables in my 1950 F-1 with a 1970 Ford truck 9 inch with no issues.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 03-22-2014, 02:09 PM
Replies: 36
Views: 1,901
Posted By lm987
Headliner Installation

Greetings,

I am referring to a cardboard installation in my 1950 F-1. Hope I didn't mislead you.
In locating the hole in the roof bracket, I carefully measured on a straight line from the bracket...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 03-22-2014, 01:18 PM
Replies: 36
Views: 1,901
Posted By lm987
Headliner installation

I also got my headliner at Sac. Vintage Ford in a kit with the other back-of -cab covers. All of it fit quite well. The only issue I had was pushing the headliner in too far above the windshield...
Showing results 1 to 15 of 97

 
Forum Jump
 


All times are GMT -5. The time now is 06:31 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup