Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Welcome to Ford-Trucks Forums!
Welcome to Ford-Trucks.com.

You are currently viewing our forums as a guest, which gives you limited access to view most discussions and access our other features. By joining our community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join the Ford-Trucks Forums community today!


Showing results 1 to 15 of 500
Search took 0.40 seconds.
Search: Posts Made By: steve(ill)
Forum: 1997 - 2003 F150 09-19-2014, 08:17 PM
Replies: 2
Views: 102
Posted By steve(ill)
most likely cause is the resistor. You know its...

most likely cause is the resistor. You know its bad. Change it out, and if still problems, check for good ground and +12 volts at resistor.
Forum: 1997 - 2003 F150 09-19-2014, 03:30 PM
Replies: 6
Views: 145
Posted By steve(ill)
don't jump the switch. Just start the truck and...

don't jump the switch. Just start the truck and then the compressor. It will cycle on and the low will drop to 30, and high will go to 150 psi. As the low drops, it will cycle off, stabilize, then...
Forum: 1997 - 2003 F150 09-18-2014, 08:45 PM
Replies: 1
Views: 75
Posted By steve(ill)
tom, for specific details, you need to say if...

tom, for specific details, you need to say if your replacing the door switch panel, the inside door lock motor, or the window motor.
Forum: 1997 - 2003 F150 09-18-2014, 08:35 PM
Replies: 2
Views: 98
Posted By steve(ill)
finding a truck with a manual trans can be a...

finding a truck with a manual trans can be a chore. LOT of autos out there. 4.6 is a good mid size motor.
Forum: 1997 - 2003 F150 09-17-2014, 08:37 PM
Replies: 6
Views: 219
Posted By steve(ill)
I did it on a 2001 F150, without pulling battery...

I did it on a 2001 F150, without pulling battery cable. Lifting the cable sounds like a good idea.
Forum: 1997 - 2003 F150 09-15-2014, 09:17 PM
Replies: 2
Views: 174
Posted By steve(ill)
spray some silicon inside the window track on the...

spray some silicon inside the window track on the top half of the door. spray it down a few inches into the track inside the door. That will help some. Removing the door panel and spraying the...
Forum: 1997 - 2003 F150 09-15-2014, 09:12 PM
Replies: 15
Views: 515
Posted By steve(ill)
F91-- I think the extra threads started about...

F91-- I think the extra threads started about 2000, but I don't know the exact number... Maybe someone else will chime in here.
Forum: 1997 - 2003 F150 09-14-2014, 07:52 PM
Replies: 15
Views: 515
Posted By steve(ill)
since its a 97, im wondering about the spark plug...

since its a 97, im wondering about the spark plug threads in the head ? Threads were marginal in 97-98... have you considered inserts at this time ? You might be OK without, but something to...
Forum: Explorer, Sport Trac, Mountaineer & Aviator 09-13-2014, 09:23 PM
Replies: 2
Views: 162
Posted By steve(ill)
Don't know if the 2006 is like the 2002, but...

Don't know if the 2006 is like the 2002, but there is no room to get the front cover off the 2002. You can suck the oil out of the fill hole and add some new, but that's all... 80-90 is OK. No...
Forum: Explorer, Sport Trac, Mountaineer & Aviator 09-13-2014, 09:09 PM
Replies: 8
Views: 214
Posted By steve(ill)
Explorer rear wheel bearing and hub replacement ...

Explorer rear wheel bearing and hub replacement <?xml:namespace prefix = "o" ns = "urn:schemas-microsoft-com:office:office" /><o:p></o:p>
sept 2006—passenger side<o:p></o:p>
<o:p> </o:p>
Jack...
Forum: Explorer, Sport Trac, Mountaineer & Aviator 09-13-2014, 09:08 PM
Replies: 8
Views: 214
Posted By steve(ill)
Rear wheel bearing is not easy. This is an...

Rear wheel bearing is not easy. This is an independent rear end. You have to take the upper and lower ball joints loose and pull the spindle / bearing / hub as a unit. Take to the hydraulic press and...
Forum: 1997 - 2003 F150 09-13-2014, 09:18 AM
Replies: 15
Views: 442
Posted By steve(ill)
Take the truck to the dealer and let them...

Take the truck to the dealer and let them reprogram the new stuff !


The Ford dealership said they can do it for $110. Just not sure if I should tow it to them in as-is condition or pull the...
Forum: 1997 - 2003 F150 09-13-2014, 09:15 AM
Replies: 14
Views: 281
Posted By steve(ill)
Guess I'm lazy, I added a drain plug to my pan,...

Guess I'm lazy, I added a drain plug to my pan, drain X amount of fluid in my spare time.....maybe 2/3 times a year and never have a problem.
May sound like a lot but it's that or watch tv.
...
Forum: 1997 - 2003 F150 09-12-2014, 09:52 PM
Replies: 80
Views: 90,693
Posted By steve(ill)
check that the knob is not stripped on the...

check that the knob is not stripped on the selector shaft also........

http://www.ford-trucks.com/forums/1275902-heater-blend-door-trouble-shooting.html
Forum: 1997 - 2003 F150 09-12-2014, 09:03 PM
Replies: 80
Views: 90,693
Posted By steve(ill)
the vacuum cylinders control the direction of the...

the vacuum cylinders control the direction of the flow. The blend door controls the air temp. Look at the temp gauge on the dash. If it is stable and mid range then the coolant is o.k., the problem...
Showing results 1 to 15 of 500

 
Forum Jump
 


All times are GMT -5. The time now is 07:25 AM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup