Go Back   Ford Truck Enthusiasts Forums > Search Forums
Sign in using an external account
Register Forgot Password?


Welcome to Ford-Trucks Forums!
Welcome to Ford-Trucks.com.

You are currently viewing our forums as a guest, which gives you limited access to view most discussions and access our other features. By joining our community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join the Ford-Trucks Forums community today!


Showing results 1 to 15 of 168
Search took 0.30 seconds.
Search: Posts Made By: theonlypheonix
Forum: 6.0L Power Stroke Diesel 04-27-2014, 06:54 PM
Replies: 321
Views: 167,908
Posted By theonlypheonix
Superfortress, Bullitt390 you both over...

Superfortress, Bullitt390 you both over complicate the matter. Since both the 48V power converter and the injection driver currents are actively regulated it boils down to simply Power(in) = desired...
Forum: 6.0L Power Stroke Diesel 12-21-2013, 01:46 AM
Replies: 68
Views: 2,741
Posted By theonlypheonix
Living here in the Midwest we get winters with...

Living here in the Midwest we get winters with some wide temperature swings, it can be as cold as -30F or as warm as 55F. To account for these temperature swings and minimizing electric use I've...
Forum: 6.0L Power Stroke Diesel 08-12-2013, 06:28 PM
Replies: 36
Views: 1,539
Posted By theonlypheonix
I've been using Ford Gold since day one on my...

I've been using Ford Gold since day one on my 2005 6.0L. First change was after four years and 91K mile and only drained/Flushed due to the fact that it was darkening and looked as though there was...
Forum: 6.0L Power Stroke Diesel 04-15-2013, 10:48 PM
Replies: 9
Views: 1,398
Posted By theonlypheonix
Have you checked out the FICM repair link at this...

Have you checked out the FICM repair link at this point. There are many problems with this unit. Despite all the solder fixes mine failed at 143000 miles. Similar symptoms as yours but not as...
Forum: 6.0L Power Stroke Diesel 02-11-2013, 05:54 PM
Replies: 172
Views: 109,574
Posted By theonlypheonix
jswartz84, Others have done this but personally I...

jswartz84, Others have done this but personally I would not recommend due to potential for fluid/water contamination of the circuit board should a leak occur. You might want to make sure it was...
Forum: 6.0L Power Stroke Diesel 10-02-2012, 06:15 PM
Replies: 16
Views: 727
Posted By theonlypheonix
While the power converter board seems to be a...

While the power converter board seems to be a major contributor to FICM failures and is of very simple design, it is also simple to fully test under load with basic equipment to find early failures....
Forum: 6.0L Power Stroke Diesel 10-01-2012, 11:28 PM
Replies: 16
Views: 727
Posted By theonlypheonix
Since you bring it up, what does this really mean...

Since you bring it up, what does this really mean in terms of verifying specifically that the power converter is actually functioning properly over its expected temperature range (say -50F to +250F),...
Forum: 6.0L Power Stroke Diesel 09-12-2012, 05:52 PM
Replies: 172
Views: 109,574
Posted By theonlypheonix
The board has a protective solder mask on the...

The board has a protective solder mask on the copper cladding but not on the component pads. From what you describe sounds like your board is contaminated if you can not easily solder to the...
Forum: 6.0L Power Stroke Diesel 09-12-2012, 03:16 PM
Replies: 172
Views: 109,574
Posted By theonlypheonix
sounds like you're not using the proper soldering...

sounds like you're not using the proper soldering techniques!:-X19 Prefered would be a temp controled iron with a proper sized tip for what you're working on. Note that the board has many small holes...
Forum: 6.0L Power Stroke Diesel 09-12-2012, 02:51 PM
Replies: 14
Views: 1,133
Posted By theonlypheonix
you can also pull the electric connector off the...

you can also pull the electric connector off the motor which controls the tranfer case and use a battery charger capable of 10 amps to drive the motor back to the 2 WD position. There are only two...
Forum: 6.0L Power Stroke Diesel 09-11-2012, 05:18 PM
Replies: 3
Views: 389
Posted By theonlypheonix
Out of the blue I had a faint humming from the...

Out of the blue I had a faint humming from the HFCM when it was around -10 F outside one winter and the truck also would not run much above 55 MPH. I had intended to change the fuel filters during...
Forum: 6.0L Power Stroke Diesel 09-08-2012, 12:19 AM
Replies: 16
Views: 727
Posted By theonlypheonix
. Sounds like to need to charge the battery...

.

Sounds like to need to charge the battery before you do ANYTHING else!:eek::
If it will not crank then the batteries are basically DEAD.:-X15 Also note that with low battery voltage the power...
Forum: 6.0L Power Stroke Diesel 09-07-2012, 05:52 PM
Replies: 16
Views: 727
Posted By theonlypheonix
alexissvfd, also you don't say under what...

alexissvfd, also you don't say under what conditions the voltage is dropping?? Is it just intermittent while the engine is running,starting, or KOEO ??

The power converter on my truck will put...
Forum: 6.0L Power Stroke Diesel 09-07-2012, 05:41 PM
Replies: 16
Views: 727
Posted By theonlypheonix
alexissvfd, can you post some clear high res...

alexissvfd, can you post some clear high res photos of your power converter board? We might be able to spot something you overlooked.
Forum: 6.0L Power Stroke Diesel 08-26-2012, 11:50 PM
Replies: 321
Views: 167,908
Posted By theonlypheonix
then to answer your original question, lead 3...

then to answer your original question, lead 3 (source) of the power FET should be connected to the right end of the Dale resistor and the junction of the two Dale resistors are connected to circuit...
Showing results 1 to 15 of 168

 
Forum Jump
 


All times are GMT -5. The time now is 05:08 AM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup