Ford Truck Enthusiasts Forums - View Profile: 93f250tn
 

Go Back   Ford Truck Enthusiasts Forums > Members
Log In 


93f250tn is starting off with a positive reputation.

93f250tn 93f250tn is offline

Senior User

Visitor Messages

Showing Visitor Messages 1 to 4 of 4
  1. Hale_XLT
    10-13-2011 03:08 PM - permalink
    Hale_XLT
    Hey Dude, I bought your truck. Would like to know if the rear tank works on it or not. It amazed me that I found it on here. I was reading about mufflers and came across it. Hell I ran outside and climbed under it, to verify the mark on front axle and pipe brace location. then I saw the pics you have of it.you can contact me at mynameismud2006@yahoo.com
  2. willerd19
    10-16-2010 01:17 PM - permalink
    willerd19
    hi, i am also building a 351w turbo charged motor. i was wondering if u could tell me if u have to o-ring the block
  3. 93_flareside
    09-16-2010 03:00 PM - permalink
    93_flareside
    CAUTION CAUTION CAUTION CAUTION!!! Make sure that the passinger side heat sheild is in place on your transmission!!!! I'm not sure how close you had to make the exhaust to the tranny, but the wiring that plugs into the pass side is for the solenoid pack. At over $500 from Ford, not good to have to replace.
    The only reason I'm telling you this, is b/c I just had to r&r my tranny to fix the soleniod seal. I now have ture duals kinda like yours, but they are wrapped from header to past the cats, as well as the shield got replaced. Expensive, but worth the piece of mind IMHO.
  4. Blue Rebel
    06-06-2009 05:13 AM - permalink
    Blue Rebel
    The leveling kit was made by skyjacker. but remember youve got the different front clip than me. 37s should fit now on your truck w/ the 3" body lift.

About Me

  • About 93f250tn
    Location
    MI
    2 Letter State/Province (use "--" for outside USA/
    MI
    Country
    USA
    Make
    Ford
    Model
    Ranger
    Year
    None - Still Looking
    Current Mileage
    None - Still looking
    Miles per year
    Rather not say
  • Signature
    1997 F250HD 4x4 7.3 powerstroke ext. cab long bed - Straight piped factory exhaust, MBRP 3" downpipe, DIY intake, TW custom 6 pos chip, Built E4OD, Swamps IDM, ISSpro gauges, 250cc/100% hybrids,
    T500 HPOP, 4r100 trans pan, Add-a-leafs on all 4 corners, 325/60r18 Toyo's, 20% tint, HID's, LED rear bulbs, 12" subwoofer.

Statistics

Total Posts
Albums
Visitor Messages
General Information
  • Last Activity: 02-14-2015 03:43 PM
  • Join Date: 05-29-2009
  • Referrals: 0

Friends

Showing Friends 1 to 1 of 1


All times are GMT -5. The time now is 03:00 AM.

 

Powered by vBulletin® Version 3.8.7 AC2
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup