Go Back   Ford Truck Enthusiasts Forums > Members
Sign in using an external account
Register Forgot Password?


Greg M-47 is starting off with a positive reputation.

Greg M-47 Greg M-47 is offline

Senior User

Visitor Messages

Showing Visitor Messages 1 to 8 of 8
  1. Sjzk
    02-05-2014 10:05 PM - permalink
    Sjzk
    Greg awhile past u had said that u recovered some seats with the cartouche cover? My question is about the extra foam padding. I'm building a 48 f1 for my daughter and have to add foam for seat heaters and wanted to know how the 1 inch and 2 inch sizes worked out?
    Thank for any info! Steve
  2. oldmerc
    11-02-2012 08:18 AM - permalink
    oldmerc
    Gregg
    That panel at the Vulcan airport is on kijiji in the Edmonton area . Check it out .
  3. Greg M-47
    02-27-2012 09:58 AM - permalink
    Greg M-47
    Yes my front and rear glass were shot out. I got replacement glass from National Parts Depot which is an hour drive from here into Michigan. Haven't installed it yet.
    Greg
  4. oldmerc
    02-17-2012 07:30 PM - permalink
    oldmerc
    Hi Gregg
    Did you have to replace your windshield and if so from where did you source it .
    Thanks

    Allan
  5. 49'er
    02-14-2012 10:42 PM - permalink
    49'er
    Hi Greg,
    If you prefer to reach me by e-mail regarding those fenders I'm at jandjparker@sympatico.ca
    John
  6. oldmerc
    01-30-2012 09:15 AM - permalink
    oldmerc
    Hi Gregg
    What shade of Red are you going to use on your stainless trim.

    Allan (oldmerc)
  7. Greg M-47
    05-12-2009 06:46 PM - permalink
    Greg M-47
    Thank you C-700. I found bigflatsrivets to be very helpful.
  8. C-700
    04-07-2009 11:40 PM - permalink
    C-700
    Greg, you need to go to www.bigflatsrivet.com they sell the hot rivets and tools to do the job. I did about 50 in my frame and they are beautful. Bolts look so sissy and short cut. It takes a couple attempts to get it right. I had to re-do my first three and then it just got fun. My rivets are larger then yours so yours will be easier. I had to make a tool for my impact hammer to set the largest rivets. Take a look at the web sight and if that does not answer your queations just PM me again.

About Me

  • About Greg M-47
    Location
    Brights Grove,Ont. Canada
    Interests
    Mercury trucks and old MG's
    2 Letter State/Province (use "--" for outside USA/
    --
    Country
    Canada
    Make
    Mercury
    Model
    M-100
    Year
    1949
    Current Mileage
    Rather not say
    Miles per year
    Rather not say

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 11-15-2014 09:08 AM
  • Join Date: 01-01-2009
  • Referrals: 0

Friends

Showing Friends 1 to 3 of 3

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »





All times are GMT -5. The time now is 09:19 AM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup