Ford Truck Enthusiasts Forums - View Profile: Greg M-47
 
Go Back   Ford Truck Enthusiasts Forums > Members
Sign In
Register Forgot Password?


Greg M-47 is starting off with a positive reputation.

Greg M-47 Greg M-47 is offline

Senior User

Visitor Messages

Showing Visitor Messages 1 to 8 of 8
  1. Sjzk
    02-05-2014 09:05 PM - permalink
    Sjzk
    Greg awhile past u had said that u recovered some seats with the cartouche cover? My question is about the extra foam padding. I'm building a 48 f1 for my daughter and have to add foam for seat heaters and wanted to know how the 1 inch and 2 inch sizes worked out?
    Thank for any info! Steve
  2. oldmerc
    11-02-2012 07:18 AM - permalink
    oldmerc
    Gregg
    That panel at the Vulcan airport is on kijiji in the Edmonton area . Check it out .
  3. Greg M-47
    02-27-2012 08:58 AM - permalink
    Greg M-47
    Yes my front and rear glass were shot out. I got replacement glass from National Parts Depot which is an hour drive from here into Michigan. Haven't installed it yet.
    Greg
  4. oldmerc
    02-17-2012 06:30 PM - permalink
    oldmerc
    Hi Gregg
    Did you have to replace your windshield and if so from where did you source it .
    Thanks

    Allan
  5. 49'er
    02-14-2012 09:42 PM - permalink
    49'er
    Hi Greg,
    If you prefer to reach me by e-mail regarding those fenders I'm at jandjparker@sympatico.ca
    John
  6. oldmerc
    01-30-2012 08:15 AM - permalink
    oldmerc
    Hi Gregg
    What shade of Red are you going to use on your stainless trim.

    Allan (oldmerc)
  7. Greg M-47
    05-12-2009 05:46 PM - permalink
    Greg M-47
    Thank you C-700. I found bigflatsrivets to be very helpful.
  8. C-700
    04-07-2009 10:40 PM - permalink
    C-700
    Greg, you need to go to www.bigflatsrivet.com they sell the hot rivets and tools to do the job. I did about 50 in my frame and they are beautful. Bolts look so sissy and short cut. It takes a couple attempts to get it right. I had to re-do my first three and then it just got fun. My rivets are larger then yours so yours will be easier. I had to make a tool for my impact hammer to set the largest rivets. Take a look at the web sight and if that does not answer your queations just PM me again.

About Me

  • About Greg M-47
    Location
    Brights Grove,Ont. Canada
    Interests
    Mercury trucks and old MG's
    2 Letter State/Province (use "--" for outside USA/
    --
    Country
    Canada
    Make
    Mercury
    Model
    M-100
    Year
    1949
    Current Mileage
    Rather not say
    Miles per year
    Rather not say

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 05-09-2015 12:26 PM
  • Join Date: 01-01-2009
  • Referrals: 0

Friends

Showing Friends 1 to 3 of 3


All times are GMT -5. The time now is 03:29 AM.

 

Powered by vBulletin® Version 3.8.7 AC2
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup