Ford Truck Enthusiasts Forums - View Profile: AXracer

Go Back   Ford Truck Enthusiasts Forums > Members
Log In 

AXracer is a splendid one to beholdAXracer is a splendid one to beholdAXracer is a splendid one to beholdAXracer is a splendid one to beholdAXracer is a splendid one to beholdAXracer is a splendid one to beholdAXracer is a splendid one to beholdAXracer is a splendid one to behold

AXracer AXracer is online now

Post Fiend

Visitor Messages

Showing Visitor Messages 1 to 10 of 34
  1. schoo
    01-15-2015 03:19 PM - permalink
    hi ax can you send that hammer profile to me
    thanks roy email=
  2. underthebridgejim
    12-09-2014 01:38 AM - permalink
    Your advice is much appreciated. PS. I just ordered a 4 1/2" shrinking disc from Wolfs, I think it may just do the trick. It may be awhile B4 I get to it, my Rheumatoid A. and the cold don't go well together, but I will. LOL, I always do eventually.
  3. underthebridgejim
    12-07-2014 03:44 PM - permalink
    I just ordered an 11lb spool of ESAP .023 easy grind. Thanks for the tip.
  4. AXracer
    11-24-2014 10:08 AM - permalink
    I know nothing about PS pumps on flatheads, and not a whole lot more about flatheads in general much beyond how to swap them out for a modern V8. Sorry
  5. newchoice
    11-23-2014 08:30 AM - permalink
    Hi AXracer
    I am doing the Toyota power steering on my 1950 F1 pickup.
    Do know what PS pump was used in the Brundell flathead conversion.
    Any help you can give me would be great.

  6. 54-F100
    11-21-2014 10:52 AM - permalink
    Hi AXracer,
    I was reading through a post where someone commented that you had made a post along the lines of "How to align a 53-56 F100 front end clip".
    Well I didn't want to bother I went 'stalker' and flipped through a few hundred of your posts with absolutely no luck - I did learn about several things to consider in the life of our own build for our 54 F100 :-)
    Do you know where I might find some good instructions on bringing my front fenders & hood into the best alignment?
  7. AXracer
    11-20-2014 10:28 AM - permalink
    I am definitely going to be posting the body repair info including the shrinking disk. Stay tuned to this channel!
  8. underthebridgejim
    11-20-2014 12:59 AM - permalink
    I cant wait for the piece you mite do ,on using a shrinking disc. I've had a disk, but never thought of using it to smoothing out my tail gate. I just wanted you to know there is interest in the practice. Hope you decide to it.
  9. AXracer
    10-08-2014 05:46 PM - permalink
    I typically work on a labor+ materials basis on rust repair since I don't know what surprises I'll find under paint/bondo/outer skin, and/or what level of finish the owner is going to want. I don't do this as a business, iI am a retired jeweler/goldsmith with 50 years experience shaping metal, building hotrods, race cars, just wanting to supplement my income, so I don't charge what the pro shops do. My labor charge is typically 25.00/hr work time, 10.00/hr parts research/chasing. + materials. I do only first quality work, fully metal finished or skim coated. Please don't ask me to do a slap and grind heavy bondo job. If you want to save money I can advise you on doing the prep work. I also offer one on one or small group instruction if you want to learn to DIY.
  10. hotrodbrando
    10-08-2014 05:06 PM - permalink
    Hey there. so, you mentioned that you do some of the metal patching. Can you give me a rough idea of what it would cost to have you do, say, a cab corner? I would be able to figure out and do this stuff myself but i also weigh the time value of having someone do it who actually knows what they are doing. Thanks!!

About Me

  • About AXracer
    Durham NC
    2 Letter State/Province (use "--" for outside USA/
    Current Mileage
    Rather not say
    Miles per year
    Rather not say
    Engine type and displacement
    CSB 400
    Major modifications
    T-56 6 speed, Toyota PS, 9" rear axle, front power disc brakes.
    Tranny type
    60 foot time
    1/8 Mile ET
    1/8 Mile MPH
    1/4 Mile ET
    1/4 Mile MPH
    Chuck Frank
  • Signature
    Passionate about autocross racing!

    1956 F100 Panel "GRACIE"
    2007 Solstice GXP racer, the "KRAZED KANARY"
    Third place finish 2009 SCCA National Championships


Total Posts
Visitor Messages
General Information
  • Last Activity: Today 09:40 AM
  • Join Date: 10-19-2004
  • Referrals: 0


Showing Friends 1 to 10 of 24

All times are GMT -5. The time now is 09:43 AM.


Powered by vBulletin® Version 3.8.7 AC2
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup