Ford Truck Enthusiasts Forums - View Profile: subford

Go Back   Ford Truck Enthusiasts Forums > Members
Log In 

subford has much to be proud ofsubford has much to be proud ofsubford has much to be proud ofsubford has much to be proud ofsubford has much to be proud ofsubford has much to be proud ofsubford has much to be proud ofsubford has much to be proud ofsubford has much to be proud of

subford subford is online now

Post Fiend

Visitor Messages

Showing Visitor Messages 1 to 10 of 208
  1. Jmitich
    01-10-2016 05:44 PM - permalink
    And it has a 460 in it obd1 no mass air flow sensor
  2. Jmitich
    01-10-2016 05:41 PM - permalink
    Hey seems like u know your stuff about cylinoide packs on e4od transmissions is there a difference between a solenoid pack on a e40d built 7 of 97 and a 96 or 95
  3. rivermobster
    11-14-2015 07:53 PM - permalink
    Restoring my F150 for my daughter to drive to school - starting with the fuel system. It's been sitting around for ages. Pulled both tanks to have em cleaned, bought all new fuel pumps and fuel filters. My parts guy got me a universal fuel selector valve (no way I want to use this).

    I found a new OE looking one on Amazon...

    I've read through all your posts about cleaning em out, but with the age of this thing, and the goo I found in the tank, I'm thinking it would be best to just replace it.

    Is there a vendor on here that sells em? Or is there someone else you know that sells a new one? Amazon and E-bay are about the only places that I have found. Thanks in advance for the help.

  4. mwilliams0326
    11-04-2015 01:09 PM - permalink
    Hi there! You responded to a post I put up about my 88 F350 with no start condition. Have replaced coil, wires, ICM, Ignition switch, EEC relay and connector, new EEC and checked ground. Truck will start with SPOUT pulled and I can drive it around it just obviously doesn't advance the timing. Thought new computer had fixed it but it wouldn't start again this morning. Any advice?
  5. Rovernut
    10-15-2015 11:02 AM - permalink
    Hi, rumor has it that you might have the information I'm looking for in this thread:

    hopefully it's not an idle rumor.

  6. porkyzilla
    07-08-2015 03:28 AM - permalink
    Hey can you help me with this? I am working on a 1990 F-150 with a 5.8 Automatic 4x4 California emissions. The truck is broke down 1hr away from me alls I can get from my uncle is the calibration code he cant pull the ecm. : 0-64R-R12 : can anyone give me the engineering/part number and interchange for ECM?
  7. allen23923
    07-05-2015 01:38 PM - permalink
    Ok retested and using pin 2 and 6 of test port I have 40 psi key on after 30 mins 30 psi heres a video of truck running
  8. allen23923
    06-30-2015 10:00 PM - permalink
    Ive posted and have no responses ..seems like you are The Guru of fords of sorts I need advice ...
    1988 f150 5.0 4x4 eod4 ..ran like a champ til I left work last week ,25 mph was top speed and popped back thur air filter box and no power at all did a fuel pressure test key on engine off 0 ..key on engine running 30 ...Replaced fuel pump with bosch 69100 and new fuel pressure regulator ,swapped map and computer ,coil ..No cels at all....When I change ecc I noticed it in park I reved it up and it started cutting back at 2500 rpms I could hear plenty of air sucking thur air box but it would sound like staving for fuel...only problem I have is rear tank will not run more then 2 miles and truck cuts off like out of gas but its been that way since I got it and have replaced both in tank sending units complete pump strainers ....Oh fuel filter was replaced 8 months ago going to replace it again tomorrow it possible the tank valve control is problem ?
  9. kaz442
    06-23-2015 07:12 PM - permalink
    Hello I hope you can help me out. I have a 1989 motorhome on a E350 chassis. I want to relocated the ICM from the distributer to a heat sink on the fender. I picked up a heat sink from the junk yard. Do they sell a extension harness to relocated this? Thanks Jeff
  10. Greg Parker
    06-05-2015 01:21 PM - permalink
    Greg Parker
    I have a 1989 F250 7.3 diesel with a bad fuel selector valve E7TB-9F271-AA) and have access to a FSV from a 1986 F250 diesel (no part number available). Do you know if they are "plug and play" compatible? thanks in advance.

About Me

  • About subford
    2 Letter State/Province (use "--" for outside USA/
    Current Mileage
    150,000 - 199,999
    Miles per year
    1,000 - 4,999
  • Signature
    95 F150 302 4R70W EB EX-CAB
    93 F250 STYLESIDE 460 E4OD 4X4
    77 F250 351M-2V NP 435/4 Speed 4X4
    Bill K, Kansas Chapter


Total Posts
Visitor Messages
General Information
  • Last Activity: Today 01:25 PM
  • Join Date: 08-26-2005
  • Referrals: 6


Showing Friends 1 to 10 of 38

All times are GMT -5. The time now is 02:19 PM.


Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup