Ford Truck Enthusiasts Forums - View Profile: AbandonedBronco

Go Back   Ford Truck Enthusiasts Forums > Members
Log In 

AbandonedBronco has a great reputation on FTE.AbandonedBronco has a great reputation on FTE.AbandonedBronco has a great reputation on FTE.AbandonedBronco has a great reputation on FTE.AbandonedBronco has a great reputation on FTE.

AbandonedBronco AbandonedBronco is offline


Visitor Messages

Showing Visitor Messages 1 to 10 of 46
    10-30-2015 06:10 AM - permalink
    Thx for deleting the spam in my VMs
  2. IdahoDoug
    07-19-2015 06:12 PM - permalink
    Hi AB:

    I live in Boise as well. How's it going? You seem to be dialed on rear end gears and I'm struggling. My rig is a 66 F100, 300 IL 6, 4 speed manual (first is basically the granny). The stock rear end gear is 3.50 and the truck is geared way too low. It is screaming on the highway at 60 mph. Based upon other commentary on this site and looking at gearing calculators, I'm leaning toward 3.0 rear end gears. Do you have any advice on this? The truck is entirely for towing and I plan on plenty of road trips in the future. Could you weigh in with your thoughts?
    Thanks much, Doug
  3. Hezekiah Shackleford
    05-16-2015 08:30 PM - permalink
    Hezekiah Shackleford
    AB, I was reading the "Distributor recurve" thread you did a few years ago. I'm pretty getting pretty close to doing that myself and I was wandering what you finally settled on for springs and which slot you used.
    Also thanks for all the time you've put into this forum. I've learned more here than probably everywhere else combined.
    H. Shackleford
  4. F-250 restorer
    03-31-2015 02:47 PM - permalink
    F-250 restorer
    AB--hello to you. Does the Walker Y pipe have a flaired end, allowing a 2.5" pipe to slip inside it?
    03-21-2015 10:08 AM - permalink
    Thank you very much for your quick response. You have confirmed what ive been thinking. I got the engine running the other day, runs like a dream! Its my first ever engine rebuild so i must have done something right so far. So far has loads of power in mid rpm, a little lacking in the upper. Havent pulled yet, going easy for a while. Good to meet you, your postings have been a great wealth of knowledge for me over the past year or so in my research of this engine. 1967 ford highboy, 300ci 4 speed, 4.10, 255 85 16. Engine: 9.2cr, .040 over, comp cam 260, cloyes advanced timing gear, 240ci ported head, 3 angle valve job, clifford intake, 2100 autolite, 300 HD 2.5 in single exaust manifold.
    03-16-2015 01:47 AM - permalink
    Hello AB, I live just up the road from you in Mountain Home. I need your opinion on a cam related topic. I just rebuilt my 300 with help from an old school hot rodder. Upon inspection of my original stock cam, i noticed the spacer ring for the first time. I didnt put it in... Oops. I was very careful when pushing the cam gear on, to watch for proper clearance between the gear and the thrust plate, unaware of that being the purpose of the spacer ring, which I had no idea about. I have a very tight clearance, but the cam spins free and smooth. My question for you is, is that the only purpose of the spacer ring? If I am comfortable with my clearance, can i get by without it? Is there a chance the pressed on aluminum gear could some how "walk up the shaft" seeing that the gear is aluminum with helical cut gears that could be prone to side load? I see no other use of the spacer ring other than clearance. Its a Cloyes aluminum gear, and I really dont want to pull it off.
  7. robbiebrown25
    11-17-2014 11:35 PM - permalink
    I need to find out about a 1990 300 inline 6 the motor has been change from efi to carb now I need to find out what distributor I need and if you know could you let me know it's killing me because I cant find one on ebay that will fit would you have any idea
  8. Harte3
    11-14-2014 07:11 PM - permalink
    Hey young man!

    I've been trying to get on the FSP site all week but keep getting a page that says "Fatal: ./cache/ is NOT writable." I it just me or have you had this problem too?

    Howard H. Hart
  9. 1986F150six
    04-21-2014 03:07 PM - permalink
    Thanks for the "rep.", AB! Have a good day!
  10. JohnSmith3524
    04-01-2014 03:26 PM - permalink
    Hey there..I've been wanting to ask..did you have any water/seapeage.leak problems when you had your log manifold water heated? I've been thinking of using that setup on a spare engine for my 85/camper,

About Me

  • About AbandonedBronco
    Boise, Idaho
    2 Letter State/Province (use "--" for outside USA/
    Current Mileage
    250,000 or more
    Miles per year
    1,000 - 4,999
    Ford Bronco
    Engine type and displacement
    300 I6
    Major modifications
    4bbl Carb, EFI 2.5" Exhaust
    Tranny type
    Street Radials
    Race weight
  • Signature
    1981 Ford Bronco. 300I6 Offenhauser DP Intake Holley 465 4bbl, 32" BFG A/T KO2, NP-435, 3.00 rear 9" EFI Manifolds. 2.5" high flow cat/muffler. DUI ignition.
    1984 Ford Bronco. *sold*
    Supermotors Pics


Total Posts
Visitor Messages
General Information
  • Last Activity: Today 11:37 AM
  • Join Date: 12-06-2007
  • Referrals: 4


Showing Friends 1 to 10 of 12

All times are GMT -5. The time now is 05:32 PM.


Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup