Ford Truck Enthusiasts Forums - View Profile: mikeo0o0o0

Go Back   Ford Truck Enthusiasts Forums > Members
Log In 

mikeo0o0o0 has much to be proud ofmikeo0o0o0 has much to be proud ofmikeo0o0o0 has much to be proud ofmikeo0o0o0 has much to be proud ofmikeo0o0o0 has much to be proud ofmikeo0o0o0 has much to be proud ofmikeo0o0o0 has much to be proud ofmikeo0o0o0 has much to be proud of

mikeo0o0o0 mikeo0o0o0 is offline

Post Fiend

Visitor Messages

Showing Visitor Messages 1 to 10 of 48
  1. sma1428
    11-17-2015 03:25 PM - permalink
    Mike, Hope you can help, you seem to be the ford expert on this site. I have a 1974 f250 camper special 2wd, regular cab and need front coil springs. It has a 390 auto transmission and AC. 8100 GVWR and 3170 front WR listed on the door plate and door jam sticker. It seems to have the heavy duty/tall spring perches. I purchased springs for a 1976 f250 with 8100 gvwr from NPD but they are a little too tall (tires are turned in) and the bottom coil hits the I beam where it turns up. Do you know where I can get a set of springs to fit this? I do not want additional lift or drop stock ride level is fine. Thanks, Steven
  2. PhoebeAnn
    06-28-2015 04:29 PM - permalink
    I'm in Polk City, with a '91 standard cab, long-bed XLT 4x4 that I think needs a cab transplant. There's so much rust that one shop I asked about it said it was beyond repair, and to just replace the cab. That's well beyond by age and capabilty at this point; I see you've done that, or had it done. Any recommendations for a shop that might want to take on this project? Alternative is to replace the truck, which probably makes more sense, but I thought I'd look at all the options.
  3. floyd rogers
    04-05-2015 01:17 PM - permalink
    floyd rogers
    I got a good one. Old, but seemingly not known to many, even Bruin Cable cannot locate any real data on my 137 inch dually Ford F350, a 1974. I need to know the dimensions of the front and rear brake cables as it seems that the list available is not for the 137 inch but only for the 136 inch wheel base. I would love to be able to post the truth on this truck as it must be one rare truck not to have any diagrams or cable numbers for it. Am i right or wrong?
  4. 4x4slik
    03-31-2015 09:00 AM - permalink
    Good day sir. Need a favor. I am in need of a parts illustration for my son's front axle. It seems the master parts catalog I purchased is missing a couple of pages and well they are the ones I need. It is for a 79 F150 4x4 with a 351m. Not sure exactly what the axle is but it is a Dana 44 I believe, open knuckle with disk brakes. It does not have anything that bolts to the top such as a steering arm or ball joints. We have some of the parts but need to get the rest of them. Thanks for your time.
  5. tinman1004
    03-20-2015 07:04 PM - permalink
    Hey Mike, I have a couple of 97 ford trucks that need a little pulling apart and putting back together. I'm having a little trouble as they've both been border line hacked together already. So I have no idea what equipment is actually original and what isnt.
    I have a 97 f150 with a manufacture date of 3/96 and VIN 1FTDX1866VKA36475 with an engine in it that has 3/5/98 manufacture date and 7G840AA on the valve cover label. I'm assuming this isn't the original engine? How do I go about finding the information on what this engine actually is? And do the intake stampings tell what the intake is actually for? I've been searching constantly trying to figure out how to decode the engine label, but I can't find anything. Only VIN decoders. If you can point me in the right direction, I would SERIOUSLY appreciate it.
    Email - or even text would work
    thanks man.
  6. Tedsf100
    02-27-2015 06:32 PM - permalink
    Hey mike, I wanted to know if you could decode my stamp plate on my 70 f100.
    115 A F103 M 4 C 17
    04500 180 4000 25

  7. 78F-250Lariat
    11-23-2014 11:06 PM - permalink
    Hey Mike, can I ask where you purchased a new printed circuit board shown in post? Thanks Pete
    Click the image to open in full size.
  8. bbf ford
    11-22-2014 03:55 PM - permalink
    bbf ford
    Do you know where I could find a factory roll bar (gt bar) for my 78 150 ranger and 2 factory push bars for my 78 and 79?
  9. rockittsled
    08-04-2014 04:31 PM - permalink
    very faint flash after letting key off 2 out of 5 times
  10. rockittsled
    08-04-2014 04:27 PM - permalink
    HELP LATE FOR WORK If light does not blink at a second test, what is bad

About Me

  • About mikeo0o0o0
    Davenport, Fl
    dentsides (aka the pumpkin)
    2 Letter State/Province (use "--" for outside USA/
    Current Mileage
    200,000 - 249,999
    Miles per year
    35,000 - 39,999
    2007 F150
    Engine type and displacement
    4.6 V8
    Major modifications
    Tranny type
    Street Radials
  • Signature


Total Posts
Visitor Messages
General Information
  • Last Activity: Today 12:27 AM
  • Join Date: 04-29-2009
  • Referrals: 0


Showing Friends 1 to 10 of 29

All times are GMT -5. The time now is 02:10 PM.


Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup