Ford Truck Enthusiasts Forums - View Profile: stuart1

Go Back   Ford Truck Enthusiasts Forums > Members
Log In 

stuart1 has a good reputation on FTE.stuart1 has a good reputation on FTE.stuart1 has a good reputation on FTE.

stuart1 stuart1 is online now


Visitor Messages

Showing Visitor Messages 1 to 9 of 9
  1. donatomisty
    08-06-2014 12:17 AM - permalink
    Thank You
    I found the wheel and column at my moms. Sorry if this sounds like a stupid question I dont know to much about vehicles other then drive them
    Is it a Ford Wheel with a steering column for a standard and was it used in cars and trucks as well what year? Thank you for your help
  2. Ken Blythen
    05-01-2011 07:58 PM - permalink
    Ken Blythen
    Hi Stuart

    I've installed the C6 trans that you gave me advice on the modulator line for.
    It drives & shifts well, but is clunking pretty firm into reverse......a few people have suggested Seafoam etc to free any stuck valves ( could it be as simple as this? - the governor was sticky for the first day) - Is there any thing else you would suggest?


    PS - I've found that if I select '1', then shift straight to reverse (with no pause in neutral), reverse is engaged softer when cold - still hard when hot.
    Going to reverse from any other gear (also from neutral or park) gives the hard engaging.
  3. tjc transport
    04-05-2011 05:28 AM - permalink
    tjc transport
    use the ignore user function, and he will disappear.
  4. stuart1
    03-01-2011 10:13 AM - permalink
    Just install the new modulator.
    If shifts are to low or soon turn the small screw in a few turns.
  5. Ken Blythen
    03-01-2011 10:11 AM - permalink
    Ken Blythen
    One other question Stuart -

    The transmission I'm using came from an E-150 or 250 & has a purple stripe modulator.......I'll replace this with a black stripe one.
    Do I need to do anything about changing the existing push-rod (different length?) at the same time, or just the modulator?

    Thanks again
  6. Ken Blythen
    03-01-2011 01:14 AM - permalink
    Ken Blythen
    3/16" it is - Thanks a lot
  7. Ken Blythen
    02-28-2011 11:32 AM - permalink
    Ken Blythen
    Thanks Stuart

    So do you mean you would you use 3/16"?
  8. Ken Blythen
    02-28-2011 02:16 AM - permalink
    Ken Blythen
    Hi Stuart

    I'm replacing an AOD with a C6 & so need a vacuum line for the modulator.

    Searching, I can only find some one who says it should be 3/16" dia - but the modulator has fittings for 1/4" there any problem with using a 1/4" line right through?

    I've posted in the 80-86 forum too, but I thought I'd ask you directly

    Thanks, Ken
  9. fordjake
    02-24-2011 02:52 AM - permalink
    You sound like the man i need to ask. hope you dont mind. truck- 78 f-150 400 c-6 4x4. problem- while driving in 2 hi and getting to about 15 mph an intermitent grinding noise appeared after dropping tn tranny and xfer case to change my fly wheel. however 4 hi when engaged has no problems at all. its only in 2-hi and every hundred feet for about 3 seconds or so that the grinding makes me sick. im not the best mechanic so any lamens terms would be great. thank you

About Me

  • About stuart1
    worn out mechanic
    Somewhere Saskatchewan
    wood working, golf, masonry
    2 Letter State/Province (use "--" for outside USA/
    Current Mileage
    50,000 - 74,999
    Miles per year
    Rather not say
    2008 Ranger
    Engine type and displacement
    Tranny type
    Street Radials
    60 foot time
    1/8 Mile ET
    1/8 Mile MPH
    1/4 Mile ET
    1/4 Mile MPH
  • Signature
    Wrench twister since 1957.
    Journeyman since 1964.
    Transmission builder since 1964.


Total Posts
Visitor Messages
General Information
  • Last Activity: Today 10:49 PM
  • Join Date: 06-17-2003
  • Referrals: 0


Showing Friends 1 to 2 of 2

All times are GMT -5. The time now is 11:06 PM.


Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup