Ford Truck Enthusiasts Forums - View Profile: Conanski

Go Back   Ford Truck Enthusiasts Forums > Members
Log In 

Conanski has much to be proud ofConanski has much to be proud ofConanski has much to be proud ofConanski has much to be proud ofConanski has much to be proud ofConanski has much to be proud ofConanski has much to be proud ofConanski has much to be proud ofConanski has much to be proud ofConanski has much to be proud of

Conanski Conanski is offline

Post Fiend

Visitor Messages

Showing Visitor Messages 1 to 10 of 460
  1. beanstock2
    09-15-2015 07:17 PM - permalink
    Conanski, could send me the relavant pages that have towing info from that manual 90 for F250 with a 460 cc engine. Truck was bought used and no manule came with it. Thanks
  2. Brianf15
    08-30-2015 02:00 AM - permalink
    Conanski could you possibly email me I just did a 351w swap in my 93 f150 e4od . It starts fine idle's fine but when revved it doesnt return to idle just dies. The motor i used had heads already blocked in back so i ihave egr capped exhaust manifold capped .
  3. Conanski
    08-29-2015 09:47 AM - permalink
    It would be better installed through the firewall into the cab behind the dash somewhere to isolate it from the dirt and heat of the engine bay.. the PCM itself is not a sealed unit. Grab the gasket from a donor truck in a scrapyard if you can.
  4. schoo
    08-28-2015 01:28 PM - permalink
    Hi Conan name is roy you have helped me in the past so I'm back with another ? Or two
    I have a 302 out of an 89 van going into a 49 f1 I want to use the stock FI so I'm looking for a place for the eec, thinking of the fire wall is that to much heat have you got any ideas
    Thanks roy
  5. Conanski
    08-01-2015 06:49 PM - permalink
    The stock exhaust system is restrictive overall but not because of it's size more because of the stock cats, whisper quiet muffler and how much the bends crimp down the overall tubing diameter. If you could replace all of it with a mendrel bent 2.5" single system you would see gains, and headers of any type will also help.
  6. quickieR
    08-01-2015 06:18 PM - permalink
    Have a 93 E150 351 EFI E4OD wheelchair conversion van, wondering if small enlargement to exhaust would help it? Is 2.5 up front into 2.25 now. Thanks for your help.
  7. Tanner2722
    06-11-2015 10:40 AM - permalink
    i have another question if you could look at my post again. Thanks man
  8. Tanner2722
    06-03-2015 10:54 AM - permalink
    hey man. i hate to bother you but i need help and from what i can see your the guy that knows what hes talking about. if you could look at my thread and help me out id really appreciate it. i just dont know what to do. thanks
  9. Conanski
    03-01-2015 06:34 PM - permalink
    I'd swap the trans while you got it all apart.
  10. Glaser67
    03-01-2015 03:58 PM - permalink
    I finally came across your post showing your exhaust set up, and its exactly what I want to do. If you have the time a have a question please: (will swap my 302 for 351) right now I have the Mazda 5sp which is in great shape, but when the 351 swap eats it up I'll swap for the HD 5sp out of F250, which is roughly 5" shorter than the Mazda. Can I rout the exhaust to accommodate both or should I just swap the tranny while the engines out in order to do the exhaust once? Thanks!

About Me

  • About Conanski
    Ottawa, Ontario
    2 Letter State/Province (use "--" for outside USA/
    Current Mileage
    250,000 or more
    Miles per year
    10,000 - 14,999
  • Signature
    Paul (Conan) O'Brien

    2006 E250 4.6L 4R75w 4.10, 2004 Ranger 3.0L 5-sp X-cab 4.10, 1994 Ranger 3.0L 5-sp x-cab 3.45, 2004 Subaru Legacy 2.5L 5-spd
    1996 Kawasaki ZX11D, 2002 Honda VFR800,


Total Posts
Visitor Messages
General Information
  • Last Activity: Today 03:21 PM
  • Join Date: 06-02-2006
  • Referrals: 1


Showing Friends 1 to 10 of 52

All times are GMT -5. The time now is 06:26 PM.


Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup