Go Back   Ford Truck Enthusiasts Forums > Members
Sign in using an external account
Register Forgot Password?


tip49 is gaining momentum as a positive member of FTE.

tip49 tip49 is offline

Posting Guru

Visitor Messages

Showing Visitor Messages 1 to 10 of 16
  1. Rusty_Bits
    11-18-2011 10:16 AM - permalink
    Rusty_Bits
    Good morning tip49,
    I was creeping in your photos and noticed the rear sway bar, and was wondering what it was off of and what diameter it is. If you could please get back to me I would appreciate it. Thank you, regards, rusty_bits
  2. Ford1950f1
    10-23-2011 08:27 AM - permalink
    Ford1950f1
    Hey tip49,

    I have a 1950 ford f1 truck. I'm looking for the original gage insert with working gages. I need to replace mine, but I don't know if I am going to go with modern insert with modern gages. I would like to find the original working gage cluster so I can keep the original look. I saw where you may have something I can use. Do you have any suggestions?
  3. Jeff and Nicolle
    04-25-2011 09:53 AM - permalink
    Jeff and Nicolle
    Hey tip49 I was looking at your floor repair pictures. I would like to see the bottom side at the cab mounts. It looks like you did away with part of the mount piece that goes into the cab? I got to replace my driver side floor pan and want to get rid of the spot welded flange where the floorpan and toeboard/pan meet. its just a great place for rust! also that sheetmetal above and below the cabmount plate, another great place for rust problems!
  4. Rusty_Bits
    12-08-2010 04:50 PM - permalink
    Rusty_Bits
    I like your truck it looks good, nice job.
  5. tip49
    11-28-2010 12:42 PM - permalink
    tip49
    I used the Crown Vic harness; still need to dress up the install this spring. I think I have a link for the EEC IV harness, that describes which wires need to remain, I removed the air purge solenoids, so still get engine light. I am getting high idle error codes, I'm going to clean the ICM to see if that cures the problem. Hope this helps.
  6. Jeff and Nicolle
    11-28-2010 11:32 AM - permalink
    Jeff and Nicolle
    Hello again, I was wondering if you have done your EFI wiring harness. If so did you make your own or did you buy a new harness? I am wanting to beat the price and do my own but wondered about others that have tried it. I have some info for the mustang maf/5.0 stuff , but mine is a 351W/5.8 with speed density not MAF.
  7. markthompson999
    09-01-2010 10:09 PM - permalink
    markthompson999
    Hey Tom, feel free to email me directly at markthompson999@hotmail.com - we can discuss my flathead. (I tried to reply to the message you send me but it wouldn't go through for some reason...)
  8. CdnWillyG
    08-17-2010 11:18 PM - permalink
    CdnWillyG
    George Moirs is handy but a little pricey, I just got back from Mid Fifties in Arizona with a truck load of parts...just the box price difference paid for the whole trip.
    A friend of mine is doing a 49 Merc long box here in Stony.
  9. CdnWillyG
    08-17-2010 09:41 AM - permalink
    CdnWillyG
    Hi Tom, I see you are from Alberta too, what town? I live in Stony Plain building a 55 F100. Nice job on your truck.
  10. F1 48 Ford
    08-06-2010 09:33 PM - permalink
    F1 48 Ford
    I'd sure be interested in buying a set of the heater control knobs. I sure don't want to use the black ones.
    Dean

About Me

  • About tip49
    Biography
    50 F47
    Location
    Alberta Canada
    2 Letter State/Province (use "--" for outside USA/
    AB
    Country
    Canada
    Make
    Ford
    Model
    F-1 through F-8
    Year
    2009
    Current Mileage
    Rather not say
    Miles per year
    Rather not say
    Horsepower
    0
    60 foot time
    0
    1/8 Mile ET
    0
    1/8 Mile MPH
    0
    1/4 Mile ET
    0
    1/4 Mile MPH
    0
  • Signature
    1950 Ford F47 Resto-mod

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 11-30-2014 06:41 PM
  • Join Date: 09-20-2004
  • Referrals: 0

Friends

Showing Friends 1 to 3 of 3

Participate In The Forums

Create new posts and participate in discussions. It's free!

Sign Up »





All times are GMT -5. The time now is 10:18 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup