Ford Truck Enthusiasts Forums - View Profile: 77&79F250

Go Back   Ford Truck Enthusiasts Forums > Members
Log In 

77&79F250 has a brilliant future77&79F250 has a brilliant future77&79F250 has a brilliant future77&79F250 has a brilliant future77&79F250 has a brilliant future77&79F250 has a brilliant future77&79F250 has a brilliant future77&79F250 has a brilliant future77&79F250 has a brilliant future77&79F250 has a brilliant future77&79F250 has a brilliant future

77&79F250 77&79F250 is offline

The parts guy...

Visitor Messages

Showing Visitor Messages 1 to 10 of 115
  1. fordrealdrive
    01-11-2016 01:03 PM - permalink
    I have been doing pretty good, thanks for asking. Last year was a very hectic year for me...I've tried to reply to the PM's you'd sent me but when I got the chance to go back and finish, everything I had typed was gone. Kinda aggravated me so I've just been lurking...I've been wanting to get on here & jabber a bit, but I catch myself spending too much time on FTE & not getting anything done lol! Hope all is well.
  2. BigBore44
    08-29-2015 03:08 PM - permalink
    Thanks friend for All your help you have given me...
    Its Much Appreciated, Thank you!
  3. f100d
    07-23-2015 10:05 AM - permalink
    I've fuel gage that when I fell tank that when I fell it goes past full and stays there.iv replasted gage sending 2 times what next
  4. f100d
    07-23-2015 09:50 AM - permalink
    my 77 same blue 2w and steepside
  5. 77&79F250
    06-27-2015 12:36 AM - permalink
    Built tough!
  6. brian1080
    05-24-2015 03:16 PM - permalink
    it's going nowhere. I think I'm gonna get her running and drive it to a local d/s shop and see what they say. I have a lot of other work to do before I need it to work anyway, lol.
  7. BenOakley
    05-05-2015 02:14 PM - permalink
    Nope, I'll check it out!
  8. msavoy
    03-22-2015 02:10 PM - permalink
    Greetings! Stumbled into your very impressive Sept. 2014 post "Ford Truck Information and Then Some..." and nearly wet myself... thanks for the info!! Searched on the post regarding "steering conversions" and didn't get a hit. Have you any experience with the Benchworks system (Benchwork Steering Systems) for converting Highboys? There's lots of ways to get there, but this is the cleanest install we've seen. Seems all a fella really needs is to get his hands on is a drawing of that adapter plate... or start from scratch. Any thoughts? Thanks!
  9. lmayer460
    03-18-2015 02:08 PM - permalink
    In regards to this thread:

    Please email the spicer manual for the Dana44 to

    I appreciate all your help good sir. I am questioning the other two posts suggesting that the spindle bearing is the problem, seems like a bad bearing would lead to radial play not axial. I will look into the snap ring you mentioned. Thanks again.
  10. dwhawkins89
    02-25-2015 10:25 AM - permalink
    I recently baught a shop manual for my 78 f150 custom. However, it is NO WHERE near as detailed as some of the diagrams you posted. I was hoping if could email your entire book. I am wanting to keep my truck as stock as possible, and I beleive the pdf files you have could help me immensly. if you choose to help, just let me know and ill send you my personal email. Thank you for your time and have a great day!

    SGT Hawkins, Daniel

About Me

  • About 77&79F250
    Retired Army Helicopter Crewchief/Door Gunner
    S/W Missouri
    Working in my shop, on my project F250 (x3), or the Bronco's (x2) and of course 4 wheeling when I can.
    2 Letter State/Province (use "--" for outside USA/
    Current Mileage
    100,000 - 124,999
    Miles per year
    1,000 - 4,999
    Everything in my sig
    Tranny type
    Country of Residence
  • Signature
    77&79 F250 Rich & Penny
    77 351M auto, a/c, add a leaf 33x12.50's
    78 (79 headlights) 460 4 spd, 4", a/c and 35's
    79 351M 4spd 6" Skyjacker Edelbrock-Holley-Hedman 35's
    99 Ranger 4x4, 98 Expedition 4x4, 73 Bronco Hillbilly-Bug
    71 Bronco 302 35" Boggers 5.58 gears spool/locker


Total Posts
Visitor Messages
General Information
  • Last Activity: Today 12:17 AM
  • Join Date: 02-19-2007
  • Referrals: 0


Showing Friends 1 to 10 of 56

All times are GMT -5. The time now is 07:43 AM.


Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup