Feb BS thread ALL Welcome!
02-14-2010, 11:15 AM
Join Date: Jul 2008
Location: Wharton, NJ
Posts: 111,873
02-14-2010, 11:22 AM
Join Date: Jul 2008
Location: Wharton, NJ
Posts: 111,873
Here is my CB Uniden Grant XL SSB.....
Attached Images
02-14-2010, 12:12 PM
Join Date: Mar 2009
Location: Seaside, Oregon
Posts: 10,372
I have been thinking of putting a two way in my pick-up just haven't figured out where to put it with the 5 speed I don't want to block the coin holder and power port.
02-14-2010, 01:15 PM
Join Date: Nov 2008
Location: McKenzie River
Posts: 23,849
Likes: 0
CBs are difficult to mount up in man.trans models, try just off center towards the pass. side on your truck, Chris.
02-14-2010, 02:00 PM
Join Date: Dec 2007
Location: carter lake ia.
Posts: 19,460
Likes: 0
Received 0 Likes
on
0 Posts
howdy all,
02-14-2010, 08:11 PM
Join Date: Dec 2009
Location: Dairy, OR
Posts: 2,322
Likes: 0
Got it installed, just an old uniden but it looks nice and works good! I will run out in a few and snap some pics.
02-14-2010, 09:13 PM
Join Date: Dec 2009
Location: Dairy, OR
Posts: 2,322
Likes: 0
02-14-2010, 09:18 PM
Join Date: Jul 2008
Location: Wharton, NJ
Posts: 111,873
That worked out nice with the manual shift!
02-14-2010, 09:19 PM
Join Date: Jul 2008
Location: Wharton, NJ
Posts: 111,873
I wish I had pics of my overhead console from my 79, it was a pine full width while still keeping the sunvisors.
02-14-2010, 09:21 PM
Join Date: Dec 2009
Location: Dairy, OR
Posts: 2,322
Likes: 0
It was literally the only place I could put it lol
02-14-2010, 09:23 PM
Join Date: Dec 2009
Location: Dairy, OR
Posts: 2,322
Likes: 0
Quote:
Originally Posted by
sddesigns
I wish I had pics of my overhead console from my 79, it was a pine full width while still keeping the sunvisors.
I was thinking of buying one of those shelf it units for the overhead and putting the cb up there.
02-14-2010, 09:24 PM
Join Date: Jul 2008
Location: Wharton, NJ
Posts: 111,873
Quote:
Originally Posted by
WarOzz
I was thinking of buying one of those shelf it units for the overhead and putting the cb up there.
I made mine from pine, it really came out sweet...I wish I had some pics!
02-14-2010, 09:27 PM
Join Date: Dec 2009
Location: Dairy, OR
Posts: 2,322
Likes: 0
wish you had to pics to share! I seen a few that guys made over the years, some real nice. I could fab one up out of aluminum... woodworking isn't my strong point.
02-14-2010, 09:31 PM
Join Date: Jul 2008
Location: Wharton, NJ
Posts: 111,873
The horizontal piece fit so well, when I did the placement after I cut it out from my template I made, it snapped into place and held itself in place, I couldn't believe how well it fit!
02-15-2010, 07:54 AM
Join Date: Jul 2008
Location: Wharton, NJ
Posts: 111,873
Good Morning All......
02-14-2010, 02:00 PM
