You are currently viewing our forums as a guest, which gives you limited access to view most discussions and access our other features. By joining our community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join the Ford-Trucks Forums community today!
Ok, the other was getting pretty long, and needs refreshed, so here we go again. It is asked that this thread be used only for posting the sale items or wanted items, discussion needs to be either by email or by the FTE Private messaging system please.
the workhorse:86 F250 4x4 6.9 Diesel 4-spd, 4.10 axles
the other workhorse 92 F350 2wd crew cab,3.55 rear axle, 92 6bt Cummins, NV4500
the project: 78 F150 4x4 shortbed 351 auto Iowa Chapter leader, ASE certified parts specialist
Come on down and join us in the Iowa chapter, or your own local chapter!! Thanks, Roger
Ok I got an injector pump(7.3)- a set of heads(7.3) - injector lines - intake- exhaust manifolds- starter-2 alternators-off a 1986 or 1992 diesel. a bronco II drive shaft (rear) with u joints. all for sale shoot me a price.for any or all.
Need a 1.31 or 1.33 ford 2v carb- these were used on some 429's and larger trucks and buses I'm told. To identify, look for the number on the drivers side of carbs float bowl, the number will be kind of blocked by the accelerator pump linkage rod, but should still be fairly easy to see.
"It's not that I'm lazy,,,, It's that I just dont care."
Well I have several things that I would sell don't need to but if I have something someone needs it's always for sale so I will make a short list.
9" gears 5.00:1, 3.25, and possibly a set or 2 of 3.50
D44 rev cut gears 4.88, 3.08, 3.50
also have a D44 solid axle, and ford 9" complete out of a 78 bronco both with 3.50 gears
3 C6 trannies 1 short shaft 4x4, 1 medium shaft 4x4, and one long shaft out of a van, I consider them all cores although I was told when I picked them up that they all worked.
also have a set of used SBC 6" Hbeam rods that were used in a 393 windsor.
850cfm barry grant mighty demon
couple of 9" dropouts
3 np205 transfer cases all good
78-79 ford F150 4x4 powersteering box that I think should have a kit put in it.
holley red elec fuel pump used
302 edelbrock performer rpm intake
misc sbf engine parts like cranks heads etc just ask
elec water pump, and gear drive starter for a small block ford
afco alum radiator out of a late model modified stock car
well thats mostly what I can think of off hand.
RIP Steve Bricks. FTE will not be the same.
Will be forever glad to have had the privilege to shake your hand and BS in person.
I need a SOHC motor for a 1999 or earlier Dodge/Plymouth Neon. Head gasket is letting go and the top end is getting noisy. Damn Dodges! This POS engine has been noisey since it had 35k miles on it...always ticking at startup and quieting once warm....110K on it now and it is getting louder and leaking oil out of the rear of the head gasket. So I need a donor engine or head to swap out once she takes the dirt nap. Would consider a complete parts car, complete engine or parts. Let me know!
2004 Baja H2X/496 HO "Ship4Brains"
24mm Lake of the Ozarks
I have a brand new 12"clutch, throw out and pressure plate as well as a good fork, boot, and bellhousing for a 351m, 400, (and big blocks??) Would like to trade for a good small block AOD or possible a C6 or ?? e-mail me with trade or cash offers. thanks.
FOR SALE:make a reasonalbe offer
-Front suspension from a 54 Ford F100 half ton, everything from the springs to the drums
-Radiator from a mid-80s chevy pickup
-stock 289 exhaust manifolds...mustang
-AOD Tranny...84 Lincoln town car
-302 block from an 84 Lincoln town car
-302 heads from an 84 Lincoln town car
-NUMBERS MATCHING COMPLETE..needs restored 69 Roadrunner....$5,000
-69 Roadrunner frame and body....$2,500
-69 Roadrunner frame, body, rolling chasis......$3,000
__________________ Tucker 54 FORD F100 Street Rod 97 F150 XLT 4x4 offroad 65 Mustang love my job, its like not actually working..
i was wondering if anyone know of a 1972ish Ranchero hood for sale. i'm looking for the one with the hood scoop, the same one that fits a 1972 torino. i'm located in iowa, and it knida needs to be nearby, because i don't think anyone will ship it for a decent cost. i wouldn't mind driving for a little ways, but i'm not going to texas to get a hood.
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.