hp and tq specs
01-10-2006, 12:47 PM
Join Date: Jan 2006
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
hp and tq specs
hey does anybody know the specs on horsepower and torque an 87 bronco xlt 5.0L 302?
01-10-2006, 01:02 PM
Join Date: Jul 2002
Location: Bend,OR
Posts: 14,265
hp 190/tq 270
the 5.8 has hp215/tq310
01-10-2006, 05:36 PM
Join Date: Nov 2005
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
how much you think im putin out
i was just wendering if you guys think my geuss is farly accurate on my hp/torque
it has all of my mods listed on my signature thing
'83 5.8windsor
01-11-2006, 09:32 AM
Join Date: Jul 2002
Location: Bend,OR
Posts: 14,265
dont see anything so go ahead an post it
01-11-2006, 04:34 PM
Join Date: Nov 2005
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
oh woops i thought i had it in my signature, my bad here we go
1983 Ford Bronco full size 351windsor c6 auto trans.
with 320+ hp and 390+ torque ( my geuss)
95 351w shortblock (.40 over 358ci)
edelbrock performer intake
Holley streetavenger 670 cfm carb
Windsor jr. 180cc Cast iron heads
Isky 262 supercam 302 camshaft
8.8" rear end with 3.55:1 gears
01-12-2006, 10:38 AM
Join Date: Jul 2002
Location: Bend,OR
Posts: 14,265
at the flywheel probably but not to the rear wheels. are you running headers as well? hows the rest of the exhaust?
01-12-2006, 04:32 PM
Join Date: Nov 2005
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
I am running Hedman Headers Long tube with no cats dual all the way with some pretty free flowing mufflers.
01-12-2006, 04:52 PM
Join Date: Jul 2002
Location: Bend,OR
Posts: 14,265
well that type of exhaust will hurt low end performance. does that dual setup have an h pipe by chance. what is the diam of the tubing?
01-12-2006, 04:55 PM
Join Date: Nov 2005
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
no H pipe, its probably 2 or 2 1/2 inch in diameter.
01-12-2006, 05:22 PM
Join Date: Nov 2005
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
what do you think would be a better exhaust setup for me
all i really use it for is for towing a big 26 ft. boat on a 30 ft trailer
01-12-2006, 05:33 PM
Join Date: Jan 2004
Location: Brentwood,CA
Posts: 26,006
ok when i run it through desk top dyno you make 270 hp and 328 ft pounds torque.
01-12-2006, 05:40 PM
Join Date: Nov 2005
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
whats desktop dyno? is it farely accurate and that is at the wheels and not at the flywheel right.
01-12-2006, 05:44 PM
Join Date: Jan 2004
Location: Brentwood,CA
Posts: 26,006
its pretty accurate, thats at the fly. subtract 25% from those to get wheel horsepower. the above mods really don't add a lot of power like most people think they do.
01-12-2006, 05:47 PM
Join Date: Nov 2005
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
well thats really disapointing to me do you got any suggestions for me, and i don't know that that seems real accurate from what ive experienced so far, but oh well
what do you think i should change to get some more hp and tq?
01-12-2006, 05:51 PM
Join Date: Jan 2004
Location: Brentwood,CA
Posts: 26,006
you could always dyno it and find out for sure.