Forward March...into another BS and general nonsense thread.
#62
#64
#65
#66
#67
Evening All!
Larry. I usually just bend my own, that way they always look right.
Well, hell. I got RC's truck red, but not without issue. Tiff and I got in to it a little bit when I got home, so I went back to the shop to work some more. I got everything sprayed and it turned out pretty nice. ....except the cowl. I got fish eyes all over the cowl for some strange reason. Even under the hood where it was caked with grease I didn't have a single fish eye, but the cowl is covered with them. I was upset about it for a while until I realized I didn't spray the grey area on the cowl. I have a grey hood center, and a grey roof, but the cowl is solid red. .....CRAP! ....well, I have to re-shoot the cowl anyway, so I guess the fish eyes aren't that big of a deal after all.
Larry. I usually just bend my own, that way they always look right.
Well, hell. I got RC's truck red, but not without issue. Tiff and I got in to it a little bit when I got home, so I went back to the shop to work some more. I got everything sprayed and it turned out pretty nice. ....except the cowl. I got fish eyes all over the cowl for some strange reason. Even under the hood where it was caked with grease I didn't have a single fish eye, but the cowl is covered with them. I was upset about it for a while until I realized I didn't spray the grey area on the cowl. I have a grey hood center, and a grey roof, but the cowl is solid red. .....CRAP! ....well, I have to re-shoot the cowl anyway, so I guess the fish eyes aren't that big of a deal after all.
#70
#71
good morning missouri.. i played with the flat bump some, got the heads back on then took the rest of the clutch linkage off so i can fix the wear on the rods and levers.. i got all new boots for the cab and bell housing so i want it to be tight and not all floppy when i get it back together.. now i have to order some seals for the leaky steering box and get it put back on.. it is coming together slowly but surely..
alan i wish the old truck would start co-operating with ya a little better.. but i should know better.. like i always say.... "if it was easy then everyone would be doing it"
alan i wish the old truck would start co-operating with ya a little better.. but i should know better.. like i always say.... "if it was easy then everyone would be doing it"
#73
Good Morning Everybody!
As soon as the laundry is done, I'm gonna go finish the top of the hood and fix the cowl on RC's truck. I should have all the red done on the cab and front clip. I won't be able to shoot the grey on the cowl until tomorrow. So, .....Monday will be the soonest it can start to get reassembled.
High Roller should be here today or tomorrow, and the car lot dropped off another truck for some rust repair. ....I'm never gonna catch up.
As soon as the laundry is done, I'm gonna go finish the top of the hood and fix the cowl on RC's truck. I should have all the red done on the cab and front clip. I won't be able to shoot the grey on the cowl until tomorrow. So, .....Monday will be the soonest it can start to get reassembled.
High Roller should be here today or tomorrow, and the car lot dropped off another truck for some rust repair. ....I'm never gonna catch up.
#74
#75
Morning folks like Dave, Chip, Dustin.
Alan hang in there brother, you know ol Rip wil look better than ever.
RC glad to see you moving fwd on the flat bump.
Jeff what is the deal with Bandits trans?
Larry I am going to ck my 2 trucks with 351M's to see what direction the lines face when they come off the pump.
Everyone else...back to work, after breakfast of course.
Alan hang in there brother, you know ol Rip wil look better than ever.
RC glad to see you moving fwd on the flat bump.
Jeff what is the deal with Bandits trans?
Larry I am going to ck my 2 trucks with 351M's to see what direction the lines face when they come off the pump.
Everyone else...back to work, after breakfast of course.