Go Back   Ford Truck Enthusiasts Forums > Older, Classic & Antique Trucks > 1973 - 1979 F-100 & Larger F-Series Trucks
Sign in using an external account
Register Forgot Password?


1973 - 1979 F-100 & Larger F-Series Trucks Discuss the Dentsides Ford Truck

Welcome to Ford-Trucks Forums!
Welcome to Ford-Trucks.com.

You are currently viewing our forums as a guest, which gives you limited access to view most discussions and access our other features. By joining our community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join the Ford-Trucks Forums community today!





 
Reply
 
 
 
 
LinkBack Thread Tools Search this Thread
  #1  
Old 08-27-2014, 04:05 AM
lazzarruss lazzarruss is offline
Junior User
 
Join Date: May 2013
Location: Fort Worth
Posts: 57
lazzarruss is starting off with a positive reputation.
lazzarruss
?? about thermactor setup during rebuild (Piston, Cam, Intake swap)

I have a pretty broad question and I hope theres a simple answer:
I am in the process of building my list to modify my 78 400 (my first ever rebuild), and what I find out is going to determine some of the parts I use. I want to use the stock Block, Heads, Piston rods, and crankshaft for this rebuild, and after I get the block, and heads checked for cracks, ported, polished, honed, I plan on using these parts:

So far Im looking at:
Tmeyer KB2347 pistons (standard bore)
Comp Cam and lifter kit K32-221-3
PERFORMER 400 (have not decided egr or non-egr)
Holley 0-4412C (or I may keep the 2150, not sure yet)
APR bolts all the way around
FelPro Gaskets
Edelbrock Victor Series water pump (with high flow thermostat)


My question:
What do I need to do during the rebuild to address the Thermactor system built into theses Cylinder heads? Does it matter?

I want to get away from using a vacuum amplifier for the egr setup, and get away from using the two 3 port vacuum switches mainly to clean up the appearance of my engine bay, but I want to keep EGR. I hope to do this with the aftermarket intake and Holley Carb.

My goal is a daily driver (30 minutes daily highway, and 45 minutes daily stop n go city) and occasional trailer towing with reasonable power and torque.

If its obvious to the pros I've overlooked some necessary consideration, please throw it at me. I don't want to get halfway into this build and find out I've wasted my time by overlooking something. Any suggestions welcome.
Reply With Quote
  #2  
Old 08-27-2014, 05:00 AM
David7.3's Avatar
David7.3 David7.3 is offline
Elder User
 
Join Date: Jun 2014
Location: Oakhust NJ Jersey Shore
Posts: 954
David7.3 has a good reputation on FTE.David7.3 has a good reputation on FTE.David7.3 has a good reputation on FTE.
If you want to do away with the managed air thermactor system then you need to plug the holes in the exhaust ports. All the system does is pump fresh air into the exhaust port for a more complete burn, I would tap and put a bolt in the holes intill there flush, you dont want to add turbulance to the exhaust. I wouldn't take a chance on welding because of the cast head, and driving or punching something in the holes will be a problem later you know that. Get the right size tap even if you have to drill one step higher and use a sharp "new" tap and drive the bolts in with locktite.
__________________
99 F-350 7.3 PSD 6" superlift springs, 35 toyo load E tires, true trac front, detroit locker rear, 140 gallons fuel, Desiel-site coolant filter, 6.0 trans cooler, BDS trans, Banks billet converter, Bank trans command, Banks turbo housing, wicked II wheel, big head waste gate, Power elbow, EBCV removed, diesel-o-rings in fuel bowl. 203 t-stat,TS Performance tuner, True 4" exhaust turbo back, More to Come when the funds come.
Reply With Quote
Old 08-27-2014, 05:00 AM
 
 
 
Reply

Go Back   Ford Truck Enthusiasts Forums > Older, Classic & Antique Trucks > 1973 - 1979 F-100 & Larger F-Series Trucks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
My 400 build SDDL-UP 335 Series- 5.8/351M, 6.6/400, 351 Cleveland 74 09-21-2014 07:59 PM
heads cam and intake for my 472 bbf ford Big Block V8 - 385 Series (6.1/370, 7.0/429, 7.5/460) 8 01-06-2014 05:20 PM
Edelbrock 1400 600 cfm jet setup Hawkmcgee 1973 - 1979 F-100 & Larger F-Series Trucks 16 08-04-2013 07:44 PM
What is the fascination II? greystreak92 1978 - 1996 Big Bronco 4 02-19-2013 02:16 PM
390 to 410 1980 Ford F-250 FE & FT Big Block V8 (332, 352, 360, 390, 406, 410, 427, 428) 17 01-21-2013 03:24 AM



All times are GMT -5. The time now is 05:40 PM.


Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup