Please do not repost, forward or otherwise publish messages
contained in these archives without consent from the respective
author(s). These archives may not, in whole or part, be stored on
any public retrieval system (FTP, web, gopher, newsgroup, etc.) by
individuals or companies, without consent of the respective authors.

Received: with LISTAR (v0.128a; list small-list); Fri, 12 May 2000 12:17:10 -0400 (EDT)
Date: Fri, 12 May 2000 12:17:10 -0400 (EDT)
From: Ford Truck Enthusiasts List Server ford-trucks.com>
To: small-list digest users ford-trucks.com>
Reply-to: small-list ford-trucks.com
Subject: small-list Digest V2000 #66
Precedence: bulk

==========================================================
Ford Truck Enthusiasts Small Chassis Truck Mailing List

Visit our web site: http://www.ford-trucks.com

To unsubscribe, send email to: listar ford-trucks.com with
the words "unsubscribe small-list" in the subject of the
message.
==========================================================

------------------------------------
small-list Digest Wed, 10 May 2000 Volume: 2000 Issue: 066

In This Issue:
PCV Valve
Re: [Fuel gauge]
2.3L 92 Ranger PCV Valve

----------------------------------------------------------------------

Date: Tue, 2 May 2000 04:08:24 -0400
Subject: PCV Valve
From: "Jeff M. Kornfeld" juno.com>

Hi All!

I have a 96 Ranger, 2.3L engine and I can't find the PCV Valve. Hayes'
manual said it is in back engine next to an oil seperator? I found the
EGR valve back there but not the PCV valve or oil seperator. Ford is
suppost to replace it free after 60,000 miles but I just curious as to
where it is.
________________________________________________________________





------------------------------

From: "Chris Oostveen" i2k.com>
Subject: Re: [Fuel gauge]
Date: Thu, 11 May 2000 07:43:33 -0400

Thanks for your help Tim. I will check it out and report back.

Chris


----- Original Message -----
From: Tim Turner netscape.net>
To: ford-trucks.com>
Sent: Wednesday, May 10, 2000 8:00 PM
Subject: [small-list] Re: [Fuel gauge]


"Chris Oostveen" i2k.com> wrote:
> I know this has been covered before. How do I check to see what is causing
> my fuel gauge to not function at all (stays on empty).

Assuming you have a 12V test light handy disconnect the plug to the
sender/pump, turn the key on and probe for the circuit that DIMLY lights the
test light. (In the wiring harness from the body.) This will be the 'feed'
from the guage; now run the test light from that pin to the corresponding
terminal on the sending unit and observe the guage, it should now be reading
something. (The exact value the guage reads will depend on the resistance
of
your test light.)

Here's what you've done if all that happens:

1) Verified that the voltage regulator for the guages works (The dim light.)

2) The wiring between the sender and the guage is intact.

3) The guage works to some extent.

A safe bet that the sender is bad if all this test passes... If NOT then
the
part that didn't happen will be a clue.

1) No dim light at the sender:
a) check the ground of your test light! :-)
b) bad CVR, but ONLY if temp & oil guages inop also
c) open circuit (bad wiring) between the guage and the sender

2) Dim light but no change in the guage when jumped to the sender:
a) bad guage
b) bad ground to the tank
c) bad printed circuit board/connection behind the inst. cluster

Alternatively if you KNOW which wire of the connector is for the sender then
temporarily jump it to ground to see if the guage goes to beyond Full with
the
key on. Do NOT jump the wrong wire in the connector this way as you'll blow
the fuel pump fuse at a minimum!


It is an '88 2wd with
> the 2.0, 5 speed. Am I looking for dead circuits or dead sending unit?

Usually dead sending unit. The CVR (constant voltage regulator) supplies a
constant voltage (8v?) to the guages which then gets modified by the varying
resistance of the senders to ground. Ford & Chrysler have low resistance
for
Full and high resistance for Empty so any break in the circuit causes the
constant 'E'. (GM works backwards; they go to Full when disconnected.)


Hope this helps!

Tim

PS: If you do need to change the sender it might be easier to unbolt the
bed
and slide it back rather than dropping the tank if it's the low rider truck.



____________________________________________________________________
Get your own FREE, personal Netscape WebMail account today at
http://www.ford-trucks.com//lc/lc.php?action=do&link=http://webmail.netscape.com.
==========================================================
To unsubscribe, send email to: listar ford-trucks.com with
the words "unsubscribe small-list" in the subject of the
message.



------------------------------

From: "Mike G" bellsouth.net>
Subject: 2.3L 92 Ranger PCV Valve
Date: Fri, 12 May 2000 13:15:16 -0500

Help!

Where is the PCV valve on a 92 Ranger 2.3L engine? I've looked, but no
luck.
Drop me a line to the list or direct to mpgrif bellsouth.net if you can
help.

Mike G


------------------------------

End of small-list Digest V2000 #66
**********************************
----------------------------------------------------------
Ford Truck Enthusiasts Small Chassic Truck Mailing List
Covering the Ranger, Bronco II, Exploer and Aerostar

Send posts to small-list ford-trucks.com

If you ever want to remove yourself from this mailing
list, send an email to:....


To access the rest of this feature you must be a logged in Registered User Of Ford Truck Enthusiasts

Registration is free, easy and gives you access to more features.
If you are not registered, click here to register.
If you are already registered, you can login here.

If you are already logged in and are seeing this message, your web browser is blocking session cookies. Change your browser cookie settings to allow session cookies.




Advertising - Terms of Use - Privacy Policy - Jobs

This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford is a registered trademark of the Ford Motor Company.