Return-Path:
Date: Sun, 26 Oct 1997 03:50:18 -0700 (MST)
From: owner-fordtrucks-digest ListService.net (fordtrucks-digest)
To: fordtrucks-digest ListService.net
Subject: fordtrucks-digest V1 #30
Reply-To: fordtrucks ListService.net
Sender: owner-fordtrucks-digest ListService.net


fordtrucks-digest Sunday, October 26 1997 Volume 01 : Number 030



=======================================================================
Ford Truck Enthusiasts - 1960 And Older Trucks Digest
Visit our web site: http://www.ford-trucks.com/
- - - - - - - - - - - - - - - - - - - - - - -
To unsubscribe, send email to:
fordtrucks-digest-request listservice.net
with the word "unsubscribe" in the body of the message. For help, send
email to the same address with the word "help" in the body of the
message.
=======================================================================
In this issue:

Re: 6-cyl manifold ["R. Garber" ]
Re:"52 F-1 project [Chris Griffin ]
Re: fordtrucks-digest V1 #29 [Mike Chalenburg ]

=======================================================================

----------------------------------------------------------------------

Date: Sat, 25 Oct 1997 06:48:04 -0500
From: "R. Garber"
Subject: Re: 6-cyl manifold

>Date: Wed, 15 Oct 1997 15:51:52 -0500
>To: fordtrucks listservice.net
>From: R Garber
>Subject: Re: 6-cyl manifold
>
>At 04:57 AM 10/12/97 -0400, you wrote:
>>I had one brazed back in the '50's - we heated the whole manifold in a
>>commercial oven, the brazed the flange and ground it smooth - it worked
>>fine. Mick
>
>Mick,
>
>I looked around (its amazing what you can find in your own back yard)
>and found a shop that specializies in restoration of cracked, broken,
>and eroded (wording on his card) cast iron and aluminum products.
>He had a engine block that had a hole the size of your fist! on both
>sides! " A easy fix" he said. So he has my mainifold. I'll post the
>results after inspection.
>
>Thanks
>Rich

Well here's the rest of the story, I thought that while I was waiting for the
intake I'd prep the exhaust for paint, Started sandblasting and found a
major crack across the flange, down the side and then it stoped and
split into 10 directions! Well, back I went. To make a long story short,
both manifolds are repaired and you can't tell they were ever cracked.
I never knew you could fix this stuff.
It is on the expensive side, but all the numbers still match so it was
worth it. Crow Cast Welding 715-425-6653 he does alot of work in
tractors and had parts in for repair from all over the country. I don't
know how many places do this type of repair, but this is a good
source.

Rich

------------------------------

Date: Sat, 25 Oct 1997 10:29:01 -0500 (CDT)
From: Chris Griffin
Subject: Re:"52 F-1 project

Thanks to all who responded to my initial queries.('52 F-1 father/son
project) I've already gained some cool ideas and I have lots of prep and
basic work to do yet!... I promise I'll have many more technical questions
as we really get into it!

Thanks again

------------------------------

Date: Sat, 25 Oct 1997 11:25:03 -0500
From: Mike Chalenburg
Subject: Re: fordtrucks-digest V1 #29

I am relatively new to this list, so if there is something I should have
seen about this, I'm sorry to bother you.

I have a 52 F1 that my father bought new and I inherited. It put in over
200,000 miles in the farm machinery business in Minnesota. I have put
another 30-40,000 over the years. Engine and drivetrain are original and
in good shape. The body, however, has been rough but I'm getting that fixed.

My question relates to the electrical system. I am considering converting
to a 12 volt system. Do any of you have pros, cons, advice and/or book
suggestions? I would appreciate knowing things I should look for.
Obviously, bulbs will have to be replaced. Also generator and regulator.
How about the starter? Gauges? What else am I missing?

Thanks for your help.

Mike



Mike Chalenburg Chalenburg harding.edu
Director of Software Services Voice: 501-279-4440
Harding University Fax: 501-279-4600

------------------------------

End of fordtrucks-digest V1 #30
*******************************

....


To access the rest of this feature you must be a logged in Registered User Of Ford Truck Enthusiasts

Registration is free, easy and gives you access to more features.
If you are not registered, click here to register.
If you are already registered, you can login here.

If you are already logged in and are seeing this message, your web browser is blocking session cookies. Change your browser cookie settings to allow session cookies.




Advertising - Terms of Use - Privacy Policy - Jobs

This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford is a registered trademark of the Ford Motor Company.