Received: with LISTAR (v1.0.0; list 80-96-list); Wed, 07 Feb 2001 12:16:38 -0500 (EST)
Date: Wed, 07 Feb 2001 12:16:38 -0500 (EST)
From: Ford Truck Enthusiasts List Server <listar ford-trucks.com>
To: 80-96-list digest users <listar ford-trucks.com>
Reply-to: 80-96-list ford-trucks.com
Subject: 80-96-list Digest V2001 #26
Precedence: list

==========================================================
Ford Truck Enthusiasts 1980-1996 Truck  Mailing  List

Visit our  web site: http://www.ford-trucks.com

To unsubscribe, send email to: listar ford-trucks.com with
the words "unsubscribe 80-96-list" in the subject  of  the
message.
==========================================================

Serious help maintaining your Ford truck!
----------------------------------------------------------
Check out the following items in our online store:
-How to Build and Modify Ford Fuel-Injected 5.0 Liter V-8 Engines
-How to Rebuild Your Small-Block Ford
-Performance Modifying Ford Trucks
-Ford Engine Overhaul Manual
-Ford Windsor Small-Block Performance
-Saddleman Seat Covers for 1992-1996 F150 - F450 Lariat

<a href="http://www.motorhaven.com/">
http://www.motorhaven.com/</a>

----------------------------------------------------------

------------------------------------
80-96-list Digest Tue, 06 Feb 2001 Volume: 2001  Issue: 026

In This Issue:
Re: Timing gears?
Fuel line question
Re: Fuel line question
Re: Fuel line question
F250 4X4 problem
Retailer question
Re: Retailer question
Re: F250 4X4 problem
Re: Retailer question

----------------------------------------------------------------------

Date: Tue, 6 Feb 2001 06:49:34 -0800 (PST)
From: Roger Lane <Lanero excite.com>
Subject: Re: Timing gears?


I had a problem very close to this on an '84 F150.  Turned out to be that
the roll pin that held the dist. gear on had partially broken.  I had alot
of timing problems untill the pin sheared completely, then the truck did not
run at all.  Took about an hour to replace the pin.
Roger
On Tue, 06 Feb 2001 13:57:43 , 80-96-list ford-trucks.com wrote:

>  ----------------------------------------------------------
>  Support FTE - Check out our store:
>  http://www.motorhaven.com/
>  ----------------------------------------------------------
>
>  The 4.9 uses a gear drive instead of a chain. So you don't have to worry
>  about chain stretch causing the problem. Maybe you have a broken tooth or

>  they are worn enough to skip a beat. Possibilities, but maybe someone
else
>  knows more before you tear into it.
>  _________________________________________________________________
>  Get your FREE download of MSN Explorer at http://www.ford-trucks.com//lc/lc.php?action=do&link=http://explorer.msn.com
>
>  =============================================================
>  To  unsubscribe:   www.ford-trucks.com/mailinglist.html#item3
>  Please remove this footer when replying.
>


"Accomplishing the impossible only means the boss will add it to your
regular duties."





_______________________________________________________
Send a cool gift with your E-Card
http://www.ford-trucks.com//lc/lc.php?action=do&link=http://www.bluemountain.com/giftcenter/



------------------------------

From: "Atkinson, Chip" <CAtkinson Circadence.com>
Subject: Fuel line question
Date: Tue, 6 Feb 2001 09:48:01 -0700


Greetings,

I'm in the beginning stages of putting an auxilliary tank on my truck.  I
got a bed for free that has the openings for a dual tank so I'm going to put
in the behind the axle tank.

Here's the question -- Is there any problem with using copper refrigerator
tubing as the metal portion of the fuel line?  It seems cheap enough,
readily available, and easy to work.  I was thinking of 1/4" tubing too.

Thanks,
Chip

------------------------------

From: "Mark Corboy" <mcorboy mindspring.com>
Subject: Re: Fuel line question
Date: Tue, 6 Feb 2001 13:07:29 -0600


The copper line is a very bad idea for fuel line. The copper line will work
harden and crack or split where the tubing encounters a bend or where there
is a flare made. The aluminum line or steel line is not that expensive.
(cheaper than a fire). You can find the correct tubing at automotive or
hydraulic supply stores.

-----Original Message-----
From: 80-96-list-bounce ford-trucks.com
[mailto:80-96-list-bounce ford-trucks.com]On Behalf Of Atkinson, Chip
Sent: Tuesday, February 06, 2001 10:48 AM
To: '80-96-list ford-trucks.com'
Subject: [80-96-list] Fuel line question


----------------------------------------------------------
Support FTE - Check out our store:
http://www.motorhaven.com/
----------------------------------------------------------

Greetings,

I'm in the beginning stages of putting an auxilliary tank on my truck.  I
got a bed for free that has the openings for a dual tank so I'm going to put
in the behind the axle tank.

Here's the question -- Is there any problem with using copper refrigerator
tubing as the metal portion of the fuel line?  It seems cheap enough,
readily available, and easy to work.  I was thinking of 1/4" tubing too.

Thanks,
Chip
=============================================================
To  unsubscribe:   www.ford-trucks.com/mailinglist.html#item3
Please remove this footer when replying.


------------------------------

From: "Atkinson, Chip" <CAtkinson Circadence.com>
Subject: Re: Fuel line question
Date: Tue, 6 Feb 2001 13:38:27 -0700


Cool.  Thanks for the tip and info.

Chip

> -----Original Message-----
> From: Mark Corboy [mailto:mcorboy mindspring.com]
> Sent: Tuesday, February 06, 2001 12:07 PM
> To: 80-96-list ford-trucks.com
> Subject: [80-96-list] Re: Fuel line question
>
>
> ----------------------------------------------------------
> Support FTE - Check out our store:
> http://www.motorhaven.com/
> ----------------------------------------------------------
>
> The copper line is a very bad idea for fuel line. The copper
> line will work
> harden and crack or split where the tubing encounters a bend
> or where there
> is a flare made. The aluminum line or steel line is not that
> expensive.
> (cheaper than a fire). You can find the correct tubing at
> automotive or
> hydraulic supply stores.
>
> -----Original Message-----
> From: 80-96-list-bounce ford-trucks.com
> [mailto:80-96-list-bounce ford-trucks.com]On Behalf Of Atkinson, Chip
> Sent: Tuesday, February 06, 2001 10:48 AM
> To: '80-96-list ford-trucks.com'
> Subject: [80-96-list] Fuel line question
>
>
> ----------------------------------------------------------
> Support FTE - Check out our store:
> http://www.motorhaven.com/
> ----------------------------------------------------------
>
> Greetings,
>
> I'm in the beginning stages of putting an auxilliary tank on
> my truck.  I
> got a bed for free that has the openings for a dual tank so
> I'm going to put
> in the behind the axle tank.
>
> Here's the question -- Is there any problem with using copper
> refrigerator
> tubing as the metal portion of the fuel line?  It seems cheap enough,
> readily available, and easy to work.  I was thinking of 1/4"
> tubing too.
>
> Thanks,
> Chip
> =============================================================
> To  unsubscribe:   www.ford-trucks.com/mailinglist.html#item3
> Please remove this footer when replying.
>
> =============================================================
> To  unsubscribe:   www.ford-trucks.com/mailinglist.html#item3
> Please remove this footer when replying.
>

------------------------------

Date: Tue, 6 Feb 2001 13:08:35 -0800 (PST)
From: Paul Rozell <prozell yahoo.com>
Subject: F250 4X4 problem



Members of the list,
I know this is a little off topic so please bare with me. My brother has a 98 F250 4X4. Recently
the torsion bar on the right hand side of the truck broke, it broke while sitting in his drive
way, this is a truck that has yet to see any wheeling. The dealer wants $500 bucks to replace the
torsion bar. My qeustion is this where could I get a torsion bar, the local parts houses cannot
get one and I know that replacing the things isn't that hard. Does anyone know where to get the
torsion bars.

Thanks in advance,

Paul Rozell
96 F150 SC 5.0
65 F100 460 C6

__________________________________________________
Do You Yahoo!?
Yahoo! Auctions - Buy the things you want at great prices.
http://www.ford-trucks.com//lc/lc.php?action=do&link=http://auctions.yahoo.com/

------------------------------

From: "Atkinson, Chip" <CAtkinson Circadence.com>
Subject: Retailer question
Date: Tue, 6 Feb 2001 16:31:24 -0700


Greetings,

Has anyone had good or bad luck with Murphys Autobody parts?
(http://www.ford-trucks.com//lc/lc.php?action=do&link=http://www.murphysautobodyparts.com)  I found a good price on tail lights
there but don't want to get swindled.

Thanks,

Chip


------------------------------

From: Slamed150 aol.com
Date: Tue, 06 Feb 2001 18:43:48 EST
Subject: Re: Retailer question


goto directpart.com

------------------------------

Date: Tue, 06 Feb 2001 19:06:05 -0600
From: Jim Cannon <jcannon SoftHome.net>
Subject: Re: F250 4X4 problem


At 13:08 06-02-01 -0800, you wrote:
>Members of the list,
>I know this is a little off topic so please bare with me. My brother has a
>98 F250 4X4. Recently
>the torsion bar on the right hand side of the truck broke, it broke while
>sitting in his drive
>way, this is a truck that has yet to see any wheeling. The dealer wants
>$500 bucks to replace the
>torsion bar. My qeustion is this where could I get a torsion bar, the
>local parts houses cannot
>get one and I know that replacing the things isn't that hard. Does anyone
>know where to get the
>torsion bars.

Junkyard.


Jim Cannon
Houston, TX                            "A Ramblin' Wreck from Georgia Tech
'29 Ford Model A Phaeton                 and a helluva' engineer!"
'80 Ford F-150 300 I-6 2WD              '63 Buick Riviera 401 V-8


------------------------------

Date: Tue, 06 Feb 2001 23:40:17 -0800
Subject: F150 Radius Arm bushing replacement
From: Joan and Walt Posluszny <redstone home.com>


It 's time for me to replace the radius arm bushings on my 85 F140 4x4.  My
buddy suggested graphite impregnated bushings so they don't squeak.  Is
there a FAQ someplace that details this replacement?  I'm considering doing
this job myself.   Thanks,  Walt


------------------------------

From: "Atkinson, Chip" <CAtkinson Circadence.com>
Subject: Re: Retailer question
Date: Wed, 7 Feb 2001 09:13:25 -0700


Ok, replying to my own message.  The tail lights that murphy's had were
$6.99 each for the entire assembly.  The best price that I could find
elsewhere, http://www.ford-trucks.com//lc/lc.php?action=do&link=http://www.mrtaillight.com was $23.  They seemed to have pretty
decent prices. and at that rate seemed worth the risk so I ordered a pair.
I'll keep people posted on the results of what I get etc.  Just thought I'd
let those "early adopters" know about it.

Chip

> -----Original Message-----
> From: Atkinson, Chip [mailto:CAtkinson circadence.com]
> Sent: Tuesday, February 06, 2001 4:31 PM
> To: '80-96-list ford-trucks.com'
> Subject: [80-96-list] Retailer question
>
>
> ----------------------------------------------------------
> Support FTE - Check out our store:
> http://www.motorhaven.com/
> ----------------------------------------------------------
>
> Greetings,
>
> Has anyone had good or bad luck with Murphys Autobody parts?
> (http://www.ford-trucks.com//lc/lc.php?action=do&link=http://www.murphysautobodyparts.com)  I found a good price
> on tail lights
> there but don't want to get swindled.
>
> Thanks,
>
> Chip
>
> =============================================================
> To  unsubscribe:   www.ford-trucks.com/mailinglist.html#item3
> Please remove this footer when replying.
>

------------------------------

End of 80-96-list Digest V2001 #26
**********************************

Serious help maintaining your Ford truck!
----------------------------------------------------------
Check out the following items in our online store:
-How to Build and Modify Ford Fuel-Injected 5.0 Liter V-8 Engines
-How to Rebuild Your Small-Block Ford
-Performance Modifying Ford Trucks
-Ford Engine Overhaul Manual
-Ford Windsor Small-Block Performance
-Saddleman Seat Covers for 1992-1996 F150 - F450 Lariat

<a href="http://www.motorhaven.com/"> ....


To access the rest of this feature you must be a logged in Registered User Of Ford Truck Enthusiasts

Registration is free, easy and gives you access to more features.
If you are not registered, click here to register.
If you are already registered, you can login here.

If you are already logged in and are seeing this message, your web browser is blocking session cookies. Change your browser cookie settings to allow session cookies.




Advertising - Terms of Use - Privacy Policy - Jobs

This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford is a registered trademark of the Ford Motor Company.